214724
23
Zoom out
Zoom in
Previous page
1/31
Next page
45
Operations
44
Using the menus (Continued)
[Key lock]
Protect from operating errors by locking on the control panel buttons of the
projector. (The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly
operation with the control panel buttons is disabled.
•To release the key lock, set the [Key Lock] to [Off] using remote control. Pressing
the [RETURN] button on the projector for 10 seconds also sets the [Key Lock] to
[Off]. (When operating the main unit, the 2 indicators of LAMP and TEMP light in
orange for 3 seconds, and at the same time the projector beeps.)
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Camera
Item Description
Computer Y/PB/PR Video S-video
(XC2500A/
XC3000A)
Projector
Input Input source name Yes Yes Yes Yes Yes
Mode name RGB input mode
[Note 1]
Ye s N o N oNo No
Resolution Resolution (in dots) Yes No No No No
Frequency Sync frequency Yes No No No No
Sync Sync signal polarity
[Note 2]
Ye s N o N oNo No
Signal format Y/P
B
/P
R
signal format No Yes No No No
Video mode Color method of video signal No No Yes Yes No
Lamp time Time of lamp use
[Note 3]
Ye s Ye s Ye s Ye s Ye s
Lamp reset count The count for lamp replacement Yes Yes Yes Yes Yes
Total time The total time that this projector
is used.
Ye s Ye s Ye s Ye s Ye s
Version Firmware version
[Note 4]
Ye s Ye s Ye s Ye s Ye s
Notes
1: The mode of supported RGB signals
p.57
is shown.
2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) Please replace the lamp after 2000 hours of use if [Lamp
power] is set to [Standard], or after 3000 hours of use if [Lamp power] is set to [Low], consult
with a dealer about getting replacement for lamp TLPLW11 (sold separately).
4: [Version] shows the version of the projector’s internal control program. This version is referred
to for customer service, etc.
Note
The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
Please read this chapter if the model you purchased includes a document camera.
Preparation of the document camera
1) Setup the arm
Status before preparation
(When stored)
3) Let the camera lens face below
2) Raise the camera head
4) Let the camera lens face the object
PRECAUTIONS
Do not jolt or force the camera head or camera arm. Doing so could cause malfunction.
The CMOS image sensor mounted on the camera of this projector is produced by
precision engineering. Please be informed that missing pixels and bright spots are not
considered as problems.
Note
It takes about 10 seconds from when the power is turned on until the operation is
possible. This is not a problem.
Using the document camera
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba xc3000a at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba xc3000a in the language / languages: English as an attachment in your email.

The manual is 5,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info