214716

Toshiba tw420 Manual

27
Zoom out
Zoom in
Previous page
1/51
Next page
52
53
Network and
USB memory
[Security for wireless LAN settings]
<Network authentication>
Set the authentication to enhance network security. Select a method identical to that of
wireless LAN terminal to be connected with.
<Encryption>
Set Encryption according to the setting you made for Network authentication, as
follows.
When you have set Network authentication to Open or Shared, select WEP for
Encryption.
When you have set Network authentication to WPA-PSK/WPA2-PSK, select TKIP or
AES for Encryption.
Note:
Network authentication is factory-set to None. If you use the projector with this
setting left unchanged, security may be compromised due to access by a third
party within the projector’s coverage.
<Key index>
When you have set Encryption to WEP, Key index must be set. By default, “1”
is selected. Select a key index identical to that of the wireless LAN terminal to be
connected with.
Note: Since the range of key index varies by product type (1 to 4 or 0 to 3), make
settings with attention.
<Network key>
When you have set Encryption to [WEP]:
For use at an encryption level of 64-bit, specify a string of 5 arbitrary characters or a
string of 10 characters in hexadecimal notation.
For use at the 128-bit level, specify a string of 13 arbitrary characters or a string of 26
characters in hexadecimal notation.
When you have set Encryption to [TKIP]/[AES]:
Specify a string of 8 to 63 arbitrary characters or a string of 64 characters in
hexadecimal notation.
Note 1: Alphabetic characters (A to F, a to f) used in hexadecimal notation are not
case sensitive; the uppercase characters and their lowercase equivalents are
handled to be identical.
Note 2: The longer the strings of characters set for the Network key, the stronger the
encryption becomes, and hence the harder it will be for a third party to decipher
your communications. However, the setting of larger encryption may slow down
communication speed.
Note 3: To set a higher security level, specify a longer string of characters. For
higher security, avoid using a word found in a dictionary and change the key
sometimes.
<Setting initialization>
This item resets the wireless LAN settings to their factory defaults.
•
•
•
Using the menus 2 (Continued)
[Wired LAN settings]
<DHCP>
If you set DHCP to Use, the IP address of the projector is assigned automatically by the
DHCP server. If your network environment does not assign IP addresses automatically,
set DHCP to Not use, then set the following items IP address, Subnet mask and
Gateway manually.
<IP address>
When DHCP is set to Not use, consult with your network administrator for the settings
below and set the IP address manually.
An IP address is a unique number assigned to a terminal. The format is a string of four
dot-separated three-digit numbers. (Example: 111.112.xxx.xxx)
Note: If you set the same IP address for wireless LAN with the one for wired LAN,
network function may fail to operate properly.
<Subnet mask>
A subnet mask is used to determine what subnet the IP address assigned to a terminal
belongs to. (Example: 255.255.xxx.xxx)
Note: If you set the same subnet work for wireless LAN with the one for wired LAN,
network function may fail to operate properly.
<Gateway>
This value specifies the IP address of the device, such as a router, to be used to access
servers outside the network. (Example: 111.112.xxx.xxx)
[Application]
<WEB browser>
Browser authentication
Browser authentication and Password are factory-set to Off and no string,
respectively. You should set them as soon as possible.
Password
If you have forgotten your password, set it again using the menu on the main unit.
•
•
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba tw420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba tw420 in the language / languages: English as an attachment in your email.

The manual is 14,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info