215855
13
Zoom out
Zoom in
Previous page
1/28
Next page
25
Operations
24
1
Turn on the power.
Tu rn on the power by following the instructions in “Turning the power on
p.23
.
2
Select the language (When using the first time).
When the projector is used for the first time after purchase, the start menu for lan-
guage (to display the menus and messages on the screen) selection is displayed in
English. (If the screen is out of focus, adjust it according to the step
6
.)
Use the or button to select the desired
language and press the
button.
Message for setup confirmation is displayed in a
selected language.
Notes
When the projector is turned on the next time, the start menu does not appear upon
startup. However, if [Reset all] is executed from the Default setting 2 menu
p.41
,
the start menu will be displayed the next time when the power is turned on.
The language can also be set via the Display setting menu
p.37
.
This owner’s manual assumes that English has been selected.
3
Activate the connected device.
Tu rn on and start the connected device such as a computer.
4
Press the INPUT button.
An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.
Notes
When [Auto input search] is set to [Off] in the Default setting 1 menu
p.40
(factory
setting is [On]), the Input select menu appears if you press the INPUT button.
If no signal is being output from the connected equipment, pressing the INPUT button
does not change the input and “There is no other input signal. will appear.
Basic operations
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Tu r kish
Polish
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
Notes
The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the system to prevent the
start-up screen from appearing. To do this, use the Display setting menu
p.37
.
The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed
p.25
.
Beep sound can be set not to beep in the Default setting 1 menu
p.40
.
When [Key lock] is [On], the operation buttons of the projector do not work
p.41
.
When [Password setting] is [On], then the start-up screen is displayed after the
Password entry screen disappears
p.31
.
Turning the power off
1
Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button once again.
When the setting of beep sound is [On], the projector beeps, and the screen turns off,
but the internal cooling fan continues to operate. Then, the projector goes into standby
mode.
During cooling, the ON/STANDBY indicator flashes. While the
indicator is flashing, the power can not be turned back on. At this
point of time, it does not matter even if you unplug the power
cord.
Note
The projector consumes about 10W of power in standby. We recommend that you unplug
the power cord if you will not be using the projector for an extended period.
PRECAUTION
If you turn the power on before cooling is complete, give the lamp time (about 5 minutes)
to cool before plugging it back in. If the lamp overheats, it may fail to light.
Turning the power on and off (Continued)
LCD Panels
LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the
following precautions.
In order to extend the lifetime of the LCD panel, always turn off the power when not in
use, and make sure that the lamp is off. Keeping the lamp off is also very effective at
saving electricity.
If the air filter becomes dirty and clogged, the projector’s internal temperature will rise,
shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter
from time to time
p.46
, and replace it periodically. Contact the store where you
purchased your projector, or your local Service Station for replacement air filters.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba tlp xd3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba tlp xd3000 in the language / languages: English as an attachment in your email.

The manual is 4,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info