Manual Toshiba tlp xd2000 portable projector (page 13 of 28) (English)

214707

Zoom out

Zoom in

1/28

Operations

Turn on the power.

Tu rn on the power by following the instructions in “Turning the power on”

p.23

Select the language and the lamp power (When using the

first time).

When the projector is used for the first time after purchase, the start menu for lan-

guage (to display the menus and messages on the screen) and lamp power selection

and configuration is displayed in English. (If the screen is out of focus, adjust it

according to the step

q Use the or button to select the

desired language and press the

button.

Message for setup confirmation is displayed in a

selected language.

Then, the menu for lamp power selection and

configuration is displayed. It is automatically set as

Standard. To change the setting, follow the step w.

w Use the or button to select the lamp

power and press the

button.

The lamp power, if selected, will be toggled without

pressing the

button. The display automatically

disappears in a few seconds.

Notes

• When the projector is turned on the next time, the start menu does not appear upon

startup. However, if [Reset all] is executed from the Default setting 2 menu

p.41

the start menu will be displayed the next time when the power is turned on.

• The language can also be set via the Display setting menu

p.37

and Lamp power

via the Default setting 1 menu

p.40

• This owner’s manual assumes that English has been selected.

Activate the connected device.

Tu rn on and start the connected device such as a computer.

Press the INPUT button.

An image of the connected equipment is projected.

Each time you press the INPUT button, it switches to the input of the connected

equipment that is outputting video signals.

Notes

• When [Auto input search] is set to [Off] in the Default setting 1 menu

p.40

(factory

setting is [On]), the Input select menu appears if you press the INPUT button.

• If no signal is being output from the connected equipment, pressing the INPUT button

does not change the input and “There is no other input signal.” will appear.

Basic operations

English

French

German

Italian

Spanish

Portuguese

Russian

Swedish

Tu r kish

Polish

Japanese

Chinese (simplified)

Chinese (traditional)

Korean

Notes

• The start-up screen will disappear after a moment. You can dismiss the start-up screen

before this by performing any operation. You can also configure the start-up screen not to

appear via the Display setting menu

p.37

• The first time you use the projector after purchase, after the start-up screen disappears,

the start menu is displayed

p.25

• Beep sound can be set not to beep in the Default setting 1 menu

p.40

• When [Key lock] is [On], the operation buttons of the projector do not work

p.41

• When [Password setting] is [On], then the start-up screen is displayed after the

Password entry screen disappears

p.31

■ Turning the power off

Press the ON/STANDBY button.

A message appears on the screen, confirming that you wish to shut off the power. This

message will disappear after a moment. (This operation is no longer valid after the

message disappears.)

Press the ON/STANDBY button once again.

When the setting of beep sound is [On], the projector beeps, and the screen turns off,

but the internal cooling fan continues to operate. Then, the projector goes into standby

mode.

During cooling, the ON/STANDBY indicator flashes. While the

indicator is flashing, the power can not be turned back on. At this

point of time, it does not matter even if you unplug the power

cord.

Note

• The projector consumes about 10W of power in standby. We recommend that you unplug

the power cord if you will not be using the projector for an extended period.

PRECAUTION

• If you turn the power on before cooling is complete, give the lamp time (about 5 minutes)

to cool before plugging it back in. If the lamp overheats, it may fail to light.

Turning the power on and off (Continued)

LCD Panels

LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the

following precautions.

• In order to extend the lifetime of the LCD panel, always turn off the power when not in

use, and make sure that the lamp is off. Keeping the lamp off is also very effective at

saving electricity.

• If the air filter becomes dirty and clogged, the projector’s internal temperature will rise,

shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter

from time to time

p.46

, and replace it periodically. Contact the store where you

purchased your projector, or your local Service Station for replacement air filters.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba tlp xd2000 portable projector in the language / languages: English as an attachment in your email.

The manual is 6,71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toshiba tlp xd2000 portable projector Manual

Product: