215805
14
Zoom out
Zoom in
Previous page
1/35
Next page
26
27
Operations
Basic operations
1
Turn on the power.
Turn on the power by following the instructions in Turning the power on
p.24
.
2
Select the language and the lamp power during initial
startup.
When the projector is used for the first time after purchase, the start menu for
language selection, lamp power selection and configuration is displayed in English. (If
the screen is out of focus, adjust it according to the step
.)
1
Use the
,
,
or
button to select the desired language and
then press the
button.
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
Polish
Norwegian
Finnish
Czech
Hungarian
Greek
Danish
Dutch
Rumanian
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
Indonesian
Thai
Arabic
The message for setup confirmation is displayed in the selected language.
Then, the menu for lamp power selection and configuration is displayed. It is
automatically set as Standard. To change the setting, follow the step
2
.
2
Use the
or button to select the lamp power and press the
button.
The lamp power, if selected, will be toggled without pressing the
button. The display
automatically disappears in a few seconds.
Notes
When the projector is turned on the next time, the start menu will not appear upon
startup. However, if [Reset all] is executed from the Default setting 2 menu
p.41
,
the start menu will be displayed the next time the power is turned on.
The language can also be set via the Display setting menu
p.37
and Lamp power
via the Default setting 1 menu
p.40
.
This owner’s manual assumes that English has been selected.
3
Activate the connected device.
Turn on and start the connected device such as a computer.
4
Press the INPUT button.
An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.
Notes
When [Auto input search] is set to [Off] in the Default setting 1 menu
p.40
the Input select menu appears if you press the INPUT button. The factory default
setting is [On].
If no signal is being output from the connected equipment, pressing the INPUT button
does not change the input and There is no other input signal. message will appear.
5
Adjust projector placement angle
You can adjust the placement angle and the height of the projected image using the
foot adjuster.
1
Lift up the front of the projector to
the desired angle, then press the foot
adjuster release button upward.
The foot adjuster extends. Release the
button to lock the position.
2
To fine adjust the angle, twist the
foot adjuster.
To stow the foot adjuster, hold up the
projector while pressing the foot adjuster
release button, then slowly lower the
projector.
Note
When [Auto keystone] is set to [On] in the Default setting 1 menu, the keystone
distortion will automatically be corrected based on the projector placement angle. If
you do not desire the automatic keystone correction, set [Auto keystone] to [Off].
6
Adjust the screen size and focus
1
Use the zooming lever to adjust the screen size.
2
Use the focusing lever to adjust the focus.
7
Adjust the volume with the buttons
The speaker volume can be adjusted when an audio signal is being input.
Front
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba tlp x150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba tlp x150 in the language / languages: English as an attachment in your email.

The manual is 10,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info