485621
17
Zoom out
Zoom in
Previous page
1/37
Next page
33
Operations
32
Displaying Information [Status display]
This displays information about the input signal, lamp use time, etc.
Press the button twice.
When the button is pressed once, the Setting display menu appears. Pressing
it again displays information
p.53
. The table below shows what kind of information
is displayed. Press the button again to dismiss the display.
Ye s: displayed, No: not displayed
Item Description
Computer Y/PB/PR
Video
PC Card Camera
S-video
Input Input source name Yes Yes Yes Yes Yes
RGB signal mode
RGB input mode
[Note 1]
YesNoNoNoNo
H-resolution
Horizontal resolution (in bits)
YesNoNoNoNo
V-resolution
Vertical resolution (in bits)
YesNoNoNoNo
H-frequency
Horizontal sync frequency
YesNoNoNoNo
V-frequency
Vertical sync frequency
[Note 2]
YesNoNoNoNo
Sync
Sync signal polarity
[Note 3]
YesNoNoNoNo
Signal format Y/PB/PR signal format No Yes No No No
Video mode
Color method of video signal
No No Yes No No
Card type PC card type No No No Yes No
Shutter speed
Shutter speed of document
No No No No Yes
imaging camera
Lamp time Time of lamp use
[Note 4]
Ye s Ye s Ye s Ye s Ye s
Version Firmware version
[Note 5]
Ye s Ye s Ye s Ye s Ye s
MAC address See page 60
p.60
No No No
Ye s
[Note 6]
No
SSID
See page 34,61
p.34
,
p.61
No No No
Ye s
[Note 6]
No
DHCP See page 61
p.61
No No No
Ye s
[Note 6]
No
IP address See page 61
p.61
No No No
Ye s
[Note 6]
No
Subnet mask See page 61
p.61
No No No
Ye s
[Note 6]
No
Gateway See page 61
p.61
No No No
Ye s
[Note 6]
No
Notes
1: The mode of supported RGB signals
p.69
is shown.
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the time displayed approaches 1,500
hours, consult with a store about getting a TLPLW2 replacement lamp (sold separately)
prepared.
5: [Version] shows the version of the projectors internal control program. This version is
referred to for customer service, etc.
6: Displayed when wireless LAN PC card is being used.
Notes
The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
Conducting another operation while information is being displayed dismisses the
display.
Using handy features (Continued)
Using the wireless LAN PC card
Please read this chapter if the model you purchased includes a PC card slot.
Functions
The following functions are available via wireless communications, when the wireless
LAN PC card and dedicated Wireless Utility software
p.24
included with this projector
are used.
Note:
A wireless LAN PC card except the supplied one (or recommended by Toshiba) does
not work with this product. Please ask your dealer about the available wireless LAN PC card.
1) Displaying a computers screen via the projector
The computers desktop screen can be sent, as well as the screens of a variety of
software applications, to the projector for display.
2) Displaying an image saved on a computer via the projector
JPEG files can be sent to the projector for display.
3) Sending images taken with the projectors document camera to a computer
This function is for models equipped with document camera.
See Sending the cameras images to a computer
p.49
for details.
4) Operating the projector by means of a computer
Some of the same functions available from the remote control can be performed.
Communication mode
This projector supports both Ad-hoc and Infrastructure Communication modes.
Ad-Hoc Communication Mode
This is transmission mode to communicate
between wireless LAN equipment.
Wireless communication can be performed via
the simple configurations.
This function can only be used if the projector is
in range of the computers wireless signals.
For security reason, confirm the specifications of your computer for the distance that
the radio wave can reach. The coverage of this projector may vary, depending on the
computer and the surrounding environment. When tested with a PC manufactured by
Toshiba with built-in wireless LAN system, the coverage is approximately 60 m.
This figure is not guaranteed and should be considered as merely a guideline.
Infrastructure Communication Mode
A mixed wireless and wired LAN can be created
via access points. Connecting to the rest of the
world via a wired LAN or the Internet generally
requires a high level of security.
Use the appropriate transmission mode for your network environment. The instructions
in this owners manual assume that you will be using a simple ad-hoc communication
mode setup.
Access point
To LAN,
Internet, etc.
Hub
O
N
/
S
T
A
N
D
B
Y
I
N
P
U
T
M
E
N
U
A
U
T
O
S
E
T
F
A
N
T
E
M
P
L
A
M
P
O
N
V
O
L
.
+
V
O
L
.
-
A
U
T
O
K
E
Y
S
T
O
N
E
O
N
/
S
T
A
N
D
B
Y
I
N
P
U
T
M
E
N
U
A
U
T
O
S
E
T
F
A
N
T
E
M
P
L
A
M
P
O
N
V
O
L
.
+
V
O
L
.
-
A
U
T
O
K
E
Y
S
T
O
N
E
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba TLP-T721 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba TLP-T721 in the language / languages: English as an attachment in your email.

The manual is 4,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info