485614
33
Zoom out
Zoom in
Previous page
1/36
Next page
6564
Others
The indicator lights inform you of internal abnormalities.
No power
Problem with projector
Unplug the power cord, and contact your dealer.
Lamp went out during use, or wont come on
Returns to standby after about 2 minutes. If the projector fails to
operate normally after turning the power back on, either the lamp
needs replacing, or there is a problem with the projector.
If a lamp burns out, replace it with a new one.
Unplug the power cord, and contact your dealer.
Power went out during use, or power wont come on
Internal overheating, or the outside temperature is too high.
Place the projector so that the air intake and exhaust are not
blocked.
Unplug the power cord and wait for a short while, then turn the
power back on.
Clean the air filter.
p.56
The icon will appear before the power goes out.
After displaying the abnormal state for about 2 minutes, returns
to standby.
Power went out during use, or power wont come on
Problem with internal cooling fan.
Unplug the power cord, and contact your dealer.
The
icon will appear before the power goes out.
After displaying the abnormal state for about 2 minutes, returns
to standby.
Power went out during use, or power wont come on
The lamp cover is not properly attached.
Unplug the power cord, and reattach the lamp cover.
p.58
The icon will appear before the power goes out.
After displaying the abnormal state for about 2 minutes, returns
to standby.
PRECAUTIONS
Make sure to unplug the power cord if something goes wrong.
If the power cord is unplugged before cooling is complete, give the lamp time to cool
before plugging it back in. If the lamp overheats it may fail to light. Unplugging the power
cord repeatedly when the temperature is high will shorten the life of the lamp. (Even if
you are not concerned about lamp lifetime, the light may not come on if you do not wait
at least 3 minutes.)
Trouble indications
ON
LAMPTEMP
FAN
ON
LAMPTEMP
FAN
ONLAMPTEMPFAN
ON
LAMPTEMP
FAN
ON
LAMPTEMP
FAN
or (Red lit)
(Off)
(Red lit) (Red lit)
Or
(Green lit)
(Green lit)
(Red lit) (Red lit)
Or
(Off)
Or
(Orange lit)
Or
(Orange lit or flashing)
(Red lit or flashing)
(Red lit)
(Orange
flashing)
(Red lit)
If you think something is wrong, check the following before contacting customer service.
Please see Trouble indications
p.64
as well.
If This Happens Check
No power
Power goes out
during use
No picture
No audio
Picture not
displayed
correctly
Picture blurred
Part of picture
out of focus
Image is dark
Colors too light
Bad shading
Remote control
doesnt work
Before calling service personnel
Is the power cord plugged in? Is it connected to the projector?
Is the lamp cover loose?
p.64
Is the ambient temperature high?
p.64
Is the air filter clogged?
p.64
Is the air intake or air exhaust blocked?
p.64
Is the projector turned on?
p.27
Is the mute function on?
p.30
Is the brightness setting minimized?
p.53
Are the connections set up correctly?
p.22
Are all the connected devices functioning properly?
Is the projector turned on?
p.27
Is the mute function on?
p.30
Is the volume setting minimized?
p.28
Are the connections set up correctly?
p.22
Are all the connected devices functioning properly?
Is the input signal supported by the projector?
p.68
,
p.69
Is the correct video mode selected?
p.29
Is the correct signal format selected?
p.29
Is the selecting of RGB or Y/PB/PR input correct?
p.27
Is there something generating an abnormal video signal, for
instance the video tape?
Is the lens dirty?
p.57
Is the lens focus adjusted optimally?
p.28
Is the projection distance within the projectors supported range?
p.21
Is the projectors screen placement angle tilted too far?
p.21
Are the sharpness or sampling phase adjustments off?
p.53
p.29
Are the brightness or contrast adjustments off?
p.53
Is the lamp nearing the end of its service life?
p.32
Are the color, tint, R-level, G-level, or B-level adjustments off?
p.53
Is the screen dirty?
Is the lamp nearing the end of its service life?
p.32
Are the remote controls batteries drained?
Are the batteries inserted into the remote control correctly?
p.19
Is the remote control being used within the effective range?
p.19
Are there any obstructions between the remote control and
projector?
Is the correct operation mode set?
p.20
Are there any fluorescent or other bright lights shining at the
projectors infrared remote sensor?
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba TLP-T701 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba TLP-T701 in the language / languages: English, Dutch as an attachment in your email.

The manual is 3,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info