485565
17
Zoom out
Zoom in
Previous page
1/20
Next page
33
Others
32
The indicator lights inform you of internal abnormalities.
No power
Problem with projector
Unplug the power cord, and contact your dealer.
Lamp went out during use, or wont come on
Returns to standby after about 2 minutes. If the projector fails to
operate normally after turning the power back on, either the lamp
needs replacing, or there is a problem with the projector.
If a lamp burns out, replace it with a new one.
Unplug the power cord, and contact your dealer.
Power went out during use, or power wont come on
Internal overheating, or the outside temperature is too high.
Place the projector so that the air intake and exhaust are not
blocked.
Unplug the power cord and wait for a short while, then turn the
power back on.
Clean the air filter.
p.30
The icon will appear before the power goes out.
After displaying the abnormal state for about 2 minutes, returns
to standby.
Power went out during use, or power wont come on
Problem with internal cooling fan.
Unplug the power cord, and contact your dealer.
The
icon will appear before the power goes out.
After displaying the abnormal state for about 2 minutes, returns
to standby.
Power went out during use, or power wont come on
The lamp cover is not properly attached.
Unplug the power cord, and reattach the lamp cover.
p.32
The icon will appear before the power goes out.
After displaying the abnormal state for about 2 minutes, returns
to standby.
PRECAUTIONS
Make sure to unplug the power cord if something goes wrong.
If the power cord is unplugged before cooling is complete, give the lamp time to cool
before plugging it back in. If the lamp overheats it may fail to light. Unplugging the power
cord repeatedly when the temperature is high will shorten the life of the lamp. (Even if
you are not concerned about lamp lifetime, the light may not come on if you do not wait
at least 3 minutes.)
Trouble indications
ON
LAMPTEMP
FAN
ON
LAMPTEMP
FAN
ONLAMPTEMPFAN
ON
LAMPTEMP
FAN
ON
LAMPTEMP
FAN
or (Red lit)
(Off)
(Red lit) (Red lit)
Or
(Green lit)
(Green lit)
(Red lit) (Red lit)
Or
(Off)
Or
(Orange lit)
Or
(Orange lit or flashing)
(Red lit or flashing)
(Red lit)
(Orange
flashing)
(Red lit)
3
Remove the lamp cover.
Loosen the 2 screws, then pull up to direction
of the arrow with your fingers on the area
shown in the figure to remove the lamp cover.
4
Pull out the lamp.
Loosen the 2 screws holding the lamp in place,
and pull on the handle to remove the lamp.
5
Mount the new lamp.
Align the orientation, press down until the bottom is
reached, and lock in place using the two lamp
locking screws.
6
Replace the lamp cover.
Align the cover, and press it in, then screw in the
screws loosened in step
3
until the lamp cover is
no longer loose.
7
Reset the lamp timer.
See the lamps manual for instructions on resetting
the lamp timer.
Notes and Precautions
Press the button twice to display (a rough guide) of the time of use from the Lamp
time item on the Status display menu.
p.26
As a rule of thumb, it is recommended that the lamp should be replaced after 2,000
hours of use. When Lamp time reaches 2,000 hours, the
icon and a message will
appear. When any operation is performed, the message disappears.
Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the
lamp may fail to come on
p.33
, and the lamps lifetime may be shortened.
Always replace the lamp with a new one.
The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
Used Lamps
This projectors lamps contain trace amounts of environmentally harmful inorganic
mercury. Be careful not to break used lamps, and dispose it in accordance with local
regulations.
Lamp replacement (Continued)
2
1
2
1
1
2
3
4
5
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba TLP-T50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba TLP-T50 in the language / languages: English as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info