485564
14
Zoom out
Zoom in
Previous page
1/20
Next page
27
Operations
26
You can call up on-screen menus, and conduct a number of adjustments and settings,
using the operation buttons
p.14
on the control panel (main unit side) and remote control.
How to use the menus
Using the menus
Note
Menu adjustments and settings (except Lamp power
p.28
) are saved when the power is
turned off via the ON/STANDBY button. If the power cord is unplugged before this, or the
power goes out, then the data will not be saved.
To Image adjustment menu
Display the Setting display menu
To Display setting menu
To Default setting menu
To Status display
The menu disappears
1. Start
2. Select a Category
3. Adjustments & Settings
4. Back
6. End
5. To Finish
The figure shows a typical example.
As the display may differ depending
on the item, use the following pages
as a reference.
Finish via the Status
display menu.
Item
Adjustment/Setting Value
This mark signfy that
there are options.
Press to display a
list of options.
These marks signify the
items can be adjusted/set
by using .
These marks signify an
item can be switched by
using .
These marks signify the items can be selected from
the list by using .
After an item selected, apply it by pressing .
Displays the
current adjust-
ment/setting of
each category
The menu shown below is only for operation instructions and might be different from the
actual display.
p.28
p.28
p.26
p.29
Displaying Information [Status display]
This displays information about the input signal, lamp use time, etc.
Press the button twice (or press the CALL button on the remote
control once).
When the button is pressed once, the Setting
display menu appears. Pressing it again displays
information
p.27
. The table below shows what kind
of information is displayed. Press the button (or the
CALL button on the remote control) again to
dismiss the display.
Ye s : displayed, No: not displayed
Item Description
Computer Y/PB/PR Video S-video
Input Input source name Yes Yes Yes Yes
RGB signal mode RGB input mode
[Note 1]
Ye s N o N o N o
H-resolution Horizontal resolution (in bits) Yes No No No
V-resolution Vertical resolution (in bits) Yes No No No
H-frequency Horizontal sync frequency Yes No No No
V-frequency Vertical sync frequency
[Note 2]
Ye s N o N o N o
Sync Sync signal polarity
[Note 3]
Ye s N o N o N o
Signal format Y/PB/PR signal format No Yes No No
Video mode Color method of video signal No No Yes Yes
Lamp time Time of lamp use
[Note 4]
YesYesYesYes
Version Firmware version
[Note 5]
YesYesYesYes
Notes
1: The mode of supported RGB signals
p.36
is shown.
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the time displayed approaches 2,000
hours, consult with a store about getting a TLPLV1 replacement lamp (sold separately)
prepared.
5: [Version] shows the version of the projectors internal control program. This version is
referred to for customer service, etc.
Notes
The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
Conducting another operation while information is being displayed dismisses the
display.
Using handy features (Continued)
FAN
TEMP
LAMP
ON
VOL.
+VOL.
-
ON / STANDBYINPUT
MENU
AUTO SET
AUTO
KEYSTONE
INPUT
ON/
STANDBY
RESIZE
OFF
CALL
AUTO
MUTE
RESIZE
FREEZE
SET
KEYSTONE
Control panel
Remote
Control
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba TLP-S30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba TLP-S30 in the language / languages: English as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info