Manual Toshiba tlp 250 lcd projector (page 22 of 77) (English)

214676

Zoom out

Zoom in

1/77

Before use

CONTENTS

OWNER’S MANUAL

3LCD DATA PROJECTOR

TLP550

TLP551

TLP250

TLP251

(

WITH DOCUMENT IMAGING CAMERA

)

TLP550/TLP250

(

WITH DOCUMENT IMAGING CAMERA

)

Before use

CONTENTS

SAFETY PRECAUTIONS

The lightning flash with arrowhead

symbol, within an equilateral triangle,

is intended to alert the user to the

presence of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to

alert the user to the presence of

important operating and

maintenance (servicing) instructions

in the literature accompanying the

appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH

VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN

THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

Before use

CONTENTS

IMPORTANT PRECAUTIONS

In the spaces provided below, record the Model and Serial No.

located at the bottom of your LCD projector.

Model No.

Serial No.

Retain this information for future reference.

Save Original Packing Materials

The original shipping carton and packing materials will come in

handy if you ever have to ship your LCD projector. For maximum

protection, repack the set as it was originally packed at the factory.

Avoid Volatile Liquid

Do not use volatile liquids, such as an insect spray, near the unit.

Do not leave rubber or plastic products touching the unit for a long

time. They will mar the finish.

Moisture Condensation

Never operate this unit immediately after moving it from a cold

location to a warm location. When the unit is exposed to such a

change in temperature, moisture may condense on the crucial

internal parts. To prevent the unit from possible damage, do not use

the unit for at least 2 hours when there is an extreme or sudden

change in temperature.

Exemption Clauses

• Toshiba Corporation bears no responsibility in the case of

damages arising from earthquakes, fire not liable to Toshiba

Corporation, operating by third parties, other accidents, or use

under abnormal conditions including erroneous or improper

operation and other problems.

• Toshiba Corporation bears no responsibility for incidental damages

(lost profit, work interruption, corruption or loss of the memory

contents, etc.) arising from the use of or the inability to use this

unit.

• Toshiba Corporation accepts no liability whatsoever for any

damages arising from not having followed the descriptions in this

Owner’s Manual.

• Toshiba Corporation accepts no liability whatsoever for any

damages arising from malfunctions arising from combination with

equipment or software that is not related to Toshiba Corporation.

Before use

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: PLEASE READ AND

OBSERVE ALL WARNINGS

AND INSTRUCTIONS GIVEN

IN THIS OWNER’S MANUAL

AND THOSE MARKED ON

THE UNIT. RETAIN THIS

BOOKLET FOR FUTURE

REFERENCE.

This set has been designed and

manufactured to assure personal safety.

Improper use can result in electric shock or

fire hazard. The safeguards incorporated in

this unit will protect you if you observe the

following procedures for installation, use and

servicing. This unit is fully transistorized and

does not contain any parts that can be

repaired by the user.

DO NOT REMOVE THE CABINET COVER,

OR YOU MAY BE EXPOSED TO

DANGEROUS VOLTAGE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL ONLY.

1. Read Owner’s Manual

After unpacking this product, read the

owner’s manual carefully, and follow all

the operating and other instructions.

2. Power Sources

This product should be operated only

from the type of power source indicated

on the marking label. If you are not sure

of the type of power supply to your

home, consult your product dealer or

local power company.

For products intended to operate from

battery power, or other sources, refer to

the operating instructions.

3. Source of Light

Do not look into the lens while the lamp

is on. The strong light from the lamp

may cause damage to your eyes or

sight.

4. Ventilation

Openings in the cabinet are provided for

ventilation and to ensure reliable

operation of the product and to protect it

from overheating, and these openings

must not be blocked or covered. The

openings should never be blocked by

placing the product on a bed, sofa, rug

or other similar surface. This product

should not be placed in a built-in

installation such as a bookcase or rack

unless proper ventilation is provided or

the manufacturer’s instructions have

been adhered to.

Continued

Before use

CONTENTS

5. Heat

The product should be situated away

from heat sources such as radiators,

heat registers, stoves, or other products

(including amplifiers) that produce heat.

IMPORTANT SAFETY INSTRUCTIONS (continued)

6. Water and Moisture

Do not use this product near water – for

example, near a bath tub, wash bowl,

kitchen sink, or laundry tub; in a wet

basement; or near a swimming pool and

the like.

7. Cleaning

Unplug this product from the wall outlet

before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a

damp cloth for cleaning.

8. Power-Cord Protection

Power-supply cords should be routed so

that they are not likely to be walked on

or pinched by items placed upon or

against them, paying particular attention

to cords at plugs, convenience

receptacles, and the point where they

exit from the product.

9. Overloading

Do not overload wall outlets; extension

cords, or integral convenience

receptacles as this can result in a risk of

fire or electric shock.

10. Lightning

For added protection for this product

during storm, or when it is left

unattended and unused for long periods

of time, unplug it from the wall outlet.

This will prevent damage to the product

due to lightning and power-line surges.

Continued

Before use

CONTENTS

11. Object and Liquid Entry

Never push objects of any kind into this

product through openings as they may

touch dangerous voltage points or short-

out parts that could result in a fire or

electric shock. Never spill liquid of any

kind on the product.

12. Do not place the product vertically

Do not use the product in the upright

position to project the pictures at the

ceiling, or any other vertical positions.

It may fall down and dangerous.

IMPORTANT SAFETY INSTRUCTIONS (continued)

S3125A

Continued

13. Stack Inhibited

Do not stack other equipment on this

product or do not place this product on

the other equipment.

Top and bottom plates of this product

develops heat and may give some

undesirable damage to other unit.

14. Attachments

Do not use attachments not

recommended by the product

manufacturer as they may cause

hazards.

15. Accessories

Do not place this product on an unstable

cart, stand, tripod, bracket, or table. The

product may fall, causing serious injury to

a child or adult, and serious damage to

the product. Use only with a cart, stand,

tripod, bracket, or table recommended by

the manufacturer, or sold with the product.

Any mounting of the product should follow

the manufacturer’s instructions, and

should use a mounting accessory

recommended by the manufacturer.

A product and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause the

product and cart combination to overturn.

Before use

CONTENTS

17. If glass components, including lens

and lamp, should break, contact your

dealer for repair service.

This product incorporates glass

components, including a lens and a

lamp. If such parts should break, please

handle with care to avoid injury and

contact your dealer for repair service.

The broken pieces of glass may cause

to injury.

In the unlikely event of the lamp

rupturing, thoroughly clean the area

around the projector and discard any

edible items placed in that area.

18. Servicing

Do not attempt to service this product

yourself as opening or removing covers

may expose you to dangerous voltage or

other hazards. Refer all servicing to

qualified service personnel.

IMPORTANT SAFETY INSTRUCTIONS (continued)

Continued

16. Damage Requiring Service

Unplug this product from the wall outlet

and refer servicing to qualified service

personnel under the following conditions:

a) When the power-supply cord or plug

is damaged.

b) If liquid has been spilled, or objects

have fallen into the product.

c) If the product has been exposed to

rain or water.

d) If the product does not operate

normally by following the operating

instructions. Adjust only those

controls that are covered by the

operating instructions as an improper

adjustment of other controls may

result in damage and will often

require extensive work by a qualified

technician to restore the product to

its normal operation.

e) If the product has been dropped or

damaged in any way.

f) When the product exhibits a distinct

change in performance – this

indicates a need for service.

19. Replacement Parts

When replacement parts are required,

be sure the service technician has used

replacement parts specified by the

manufacturer or have the same

characteristics as the original part.

Unauthorized substitutions may result in

fire, electric shock, or other hazards.

(Replacement of the lamp only should

be made by users.)

20. Safety Check

Upon completion of any service or

repairs to this product, ask the service

technician to perform safety checks to

determine that the product is in proper

operating condition.

Before use

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS (continued)

21. Do not get your hands between the

camera arm and the main unit when

setting the camera arm back in its

original position.

To avoid injury, be careful not to get your

hands caught when setting the camera

arm back in its original position. Families

with children should be particularly

careful.

22. Do not carry by the camera arm.

Do not carry the projector by the camera

arm.

Doing so can result in damage or injury.

23. Do not leave documents on the unit

or near of the air exhaust for long

periods of time.

The heat could erase or discolor the

letters on a thermal paper.

24. Do not move the projector while the

arm is still erect.

Always store the arm back in position

when moving the projector. Otherwise

injury or damage may result.

25. Do not look into the arm light while it is

lit.

The strong light may cause damage to

your eyes or sight.

Before use

CONTENTS

Power supply cord selection

Plug

configuration Plug type

EURO

Line voltage

220 – 240V

Use a 5A fuse which is approved by ASTA

or BSI to BSI362.

Always replace the fuse cover after

changing the fuse.

If your line voltage is 220 to 240V, use one of

the following types of cable.

Plug

configuration

Plug type

EURO

240V

10 – 15A

240V

Australian

240V

10A

North American

240V

15A

Switzerland

240V

Line voltage

220 – 240V

200 – 240V

Before use

CONTENTS

Contents

Before use

SAFETY PRECAUTIONS ...................................................... 2

IMPORTANT PRECAUTIONS ............................................... 3

IMPORTANT SAFETY INSTRUCTIONS ............................... 4

Power supply cord selection ............................................... 9

Contents .............................................................................. 10

Names of each part on the main unit................................ 11

Names of each part on the remote control ...................... 14

Loading batteries................................................................ 15

Remote control operation .................................................. 16

Installation and connections

Floor-mounted projector placement ................................. 17

Lens shift function ............................................................. 20

Projector placement angle adjustment (Foot adjuster) .. 21

Ceiling-mounted projector placement .............................. 22

Connecting a computer .................................................... 23

Connecting video equipment ............................................ 24

Projector operation control by a computer...................... 26

Operations

Projection on the screen.................................................... 27

Turning the power off ......................................................... 32

Adjusting the picture automatically.................................. 33

Correcting the keystone distortion ................................... 34

Cutting off the picture and sound temporarily ................ 35

Freezing the picture ........................................................... 36

Enlarging the picture size .................................................. 37

Displaying PIP Sub-pictures .............................................. 38

Displaying Information....................................................... 39

Operating the presentation mode ..................................... 40

Adjustments & Settings

Operating the menu screen ............................................... 42

GUIDE MENU adjustments and settings .......................... 44

FULL MENU adjustments and settings - Picture ............. 45

FULL MENU adjustments - Position ................................. 46

FULL MENU adjustments - Color ...................................... 47

FULL MENU adjustments and settings - Audio ............... 48

FULL MENU adjustments and settings - Display ............ 49

FULL MENU settings - Default setting .............................. 50

FULL MENU settings - Reset ............................................. 51

PIP menu setting ................................................................ 52

Document imaging camera

Part names (of the document imaging camera model) ... 53

Preparation of the document imaging camera ................ 54

Picture projection with the document imaging camera .. 55

Locking the white balance ................................................. 58

Correcting illuminated defects .......................................... 59

Maintenance

Trouble indications ............................................................ 60

Air filter cleaning ................................................................ 61

Lens and main unit cleaning ............................................. 63

Lamp replacement .............................................................. 64

Others

Before calling service personal ........................................ 66

Pin assignment of COMPUTER connector....................... 68

Applicable signal ................................................................ 69

Controlling the projector by using RS-232C .................... 71

Specifications ..................................................................... 76

COVER

Before use

CONTENTS

Names of each part on the main unit

Continued

Infrared remote sensor

Air intake

Infrared

remote sensor

Control panel

Lens shift dial

Zooming lever

Focusing ring

AC IN socket

Left side

Speaker

Carrying handle

Open to carry the projector.

Anti-theft lock hole

Lens

Lens cover

Foot adjuster

Foot adjuster release button

Air intake

Rear side

Air exhaust

Right side

Front side

CAUTION

Openings in the cabinet are provided for ventilation and to

ensure reliable operation of the product and to protect it from

overheating, and these openings must not be blocked or

covered.

The explanation here is only for the model without the document

imaging camera. For the model with the document imaging camera,

refer to

Note

The air exhaust discharges high temperature air. Do not put anything around the air exhaust, otherwise it may deform due to the high temperature air.

Before use

CONTENTS

Names of each part on the main unit (continued)

42 31

27 32 60

3227

TEMP indicator

KEYSTONE button

To correct the keystone distortion of

the picture.

FAN indicator

LAMP indicator

ON indicator

INPUT button

ENTER button

Selection buttons

EXIT button

VOL/ADJ buttons

AUTO SET button

MENU button

ON/STANDBY button

Top side

Control panel

To set and/or adjust values on the menu.

To adjust the volume when the menu is not

displayed.

To indicate the

status of the

projector.

To turn the projector on or off (standby).

To display the menu screen and/or select

operations on the menu screen.

Use the selection buttons and the EXIT button

to enlarge the image.

To adjust the computer input image

automatically.

To select the input source.

ON / STANDBY

VOL / ADJ

Continued

Before use

CONTENTS

USB S-VIDEOVIDEOAUDIO

COMPUTER

(

Y/P

)

CONTROL

AUDIO jack -

(ø 3.5mm stereo mini-jack)

To enter audio signal from a computer

or a video equipment.

USB connector

To connect to a USB connector of a

computer when using the presentation

mode.

CONTROL connector

(RS-232C connector)

To connect a computer to control the

projector.

VIDEO jack

To enter video signal from a video

equipment, etc.

S-VIDEO connector

To enter S-Video signal from video

equipment, etc.

COMPUTER connector

To enter RGB signal from a computer,

etc or component video signal (Y/P

B/PR

Signal) from a video equipment.

23 25

26 71

Left side

Names of each part on the main unit (continued)

Before use

CONTENTS

Names of each part on the remote control

ON /

INPUT

ENTER

CT-90106

KEYSTONE AUTO SET

EXIT /

P.MODE

PIP

FREEZE

MUTE

CALL

RESIZE

VOL

ADJ

STANDBY

27 32

42 43

To display the menu screen

and/or select the operation

on the menu screen.

Use the selection buttons and

EXIT button to enlarge the

image and to operate

the presentation mode.

INPUT button

To select the input source.

KEYSTONE button

To correct the keystone distortion

of the picture.

FREEZE button

To freeze the picture.

PIP button

To display the video input image

as a small size picture in the

computer image display window.

VOL/ADJ buttons

To set and/or adjust values on the menu.

To adjust volume when the menu is not

displayed.

MUTE button

To cut off the picture and sound

temporarily.

AUTO SET button

ON/STANDBY button

Remote control transmission part

To turn the projector on or off (Standby).

To adjust the computer input image

automatically.

RESIZE buttons

To enlarge the picture size.

ENTER button

Selection button

EXIT button

MENU button

CALL button

To display the information.

CLASS 1 LED PRODUCT

Installation and

connections

CONTENTS

Ceiling-mounted front projection

Viewing a picture projected on the front of the screen from a

ceiling installation.

Ceiling-mounted rear projection

Viewing a picture projected through the back of the screen from a

ceiling installation.

Perform the “Projection mode” setting on the menu screen for the projection method.

Note

The relation between the projection size and the distance to the screen is the same as that of the floor-mounted projection mode

Translucent screen

Viewer

Ceiling-mounted projector placement

CAUTION

When a ceiling mount is required, please consult with the dealer.

Viewer

USB

S-VIDEOVIDEO

AUDIO

COMPUTER

(

Y/P

)

CONTROL

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba tlp 250 lcd projector in the language / languages: English as an attachment in your email.

The manual is 2,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toshiba tlp 250 lcd projector Manual

Product: