626991

Toshiba TEC B-SX4T SERIES Manual

40
Zoom out
Zoom in
Previous page
1/54
Next page
APPENDIX 1 SPECIFICATIONS
ENGLISH VERSION EO1-33034
A1.3 Media
EA1- 3
A1.3.1 Media Type (Cont.)
[Unit: mm]
Cut mode
Label dispensing mode
Item
Batch mode Strip mode
Rotary cutter
(*2)
Swing cutter
Label 10.0 – 1500.0 25.4 – 1500.0
3”/sec., 6”/sec.: 38.0 - 1500.0
38.0 – 1500.0
Media pitch
Tag 10.0 – 1500.0 ---- 3”/sec., 6”/sec.: 30.0 – 1500.0 25.4 – 1500.0
Label length 8.0 – 1498.0 23.4 – 1498.0
3”/sec., 6”/sec.: 32.0 – 1494.0
25.0 – 1494.0
(*1)
Width including backing paper
(
See NOTE 5
.)
30.0 – 112.0 50.0 – 112.0 30.0 – 112.0
Label width
(
See NOTE 5
.)
27.0 – 109.0 47.0 – 109.0 27.0 – 109.0
Gap length 2.0 – 20.0 6.0 – 20.0
Black mark length (Tag paper) 2.0 – 10.0
Effective print width 10.0 – 104.0±0.2
Label 6.0 – 1496.0 21.4 – 1496.0
3”/sec., 6”/sec.: 30.0 – 1492.0
23.0 – 1492.0
Effective print length
Tag 8.0 – 1498.0
----
3”/sec., 6”/sec.: 28.0 – 1496.0
23.0 – 1496.0
Print speed up/slow down area 1.0
Label 0.13 – 0.17
Thickness
Tag 0.15 – 0.29
Maximum effective length for on the fly issue 1361.0
Maximum outer roll diameter Ø200
Roll direction Inside
Inner core diameter Ø76.2±0.3
A1.3.2 Detection Area of the Transmissive Sensor
The Transmissive Sensor is movable from the centre to the left edge of media.
The Transmissive Sensor detects a gap between labels, as illustrated below.
<Label>
N
OTES:
1. To ensure print quality and print head life use only TOSHIBA TEC specified media.
2. The media length specifications for use of the cutter are:
*1: When issuing a label using the swing cutter, label length should be 35.0 mm – (Gap length/2).
*2: The rotary cutter does not support the print speed of 10”/sec.
When using the Rotary Cutter, be sure to install the Ribbon Saving Module (B-9904-R-QM). Failure to do
this may cause a paper jam or ribbon error.
3. When marking black marks on the label rolls, they should be marked at the gaps.
4. “On the fly issue” means that the printer can feed and print without stopping between labels.
5. There are restrictions in use of the media which is narrower than 50 mm. For details, refer to TOSHIBA TEC
service re
p
resentative.
Sensor position
Area to be detected.
Centre of media
Print side
Min. 12 mm
Label
Gap
Label
Min. 2.0 mm
(Min. 6.0 mm when using
the cutter module.)
Sensor is movable
within this range.
Media feed direction
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba TEC B-SX4T SERIES at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba TEC B-SX4T SERIES in the language / languages: English as an attachment in your email.

The manual is 2,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info