214860
15
Zoom out
Zoom in
Previous page
1/47
Next page
29
Operations
28
5
Projector placement angle adjustments
The placement angle and the height of the projected image can be adjusted by the foot
adjuster.
q Lift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
w To fine adjust the angle, twist the
foot adjuster.
e To adjust the horizontal angle, use
the tilt adjuster.
To stow the foot adjuster, hold up the projector while pressing the foot adjuster
release button, then slowly lower the projector.
6
Adjusting the screen size and focus
q
Use the ZOOM button to adjust the screen size.
w
Use the FOCUS button to adjust the screen focus.
7
Adjusting the volume with the
buttons
The speaker volume can be adjusted when an audio signal is being input.
Notes
While a text entry screen (e.g., the Password entry screen) is displayed, the remote
control’s FOCUS and ZOOM buttons function as numeric keys, and therefore cannot be
used to adjust the screen size or focus. In such a case, use the FOCUS and ZOOM
buttons on the projector to make adjustment or retry after quitting the text entry screen.
Note that lamp characteristics may rarely cause the brightness to fluctuate slightly.
•A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
The DLP
®
chip is made using extremely advanced technology, but there may be black
spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.
Please note that these are not malfunctions.
Although this projector supports a wide range of RGB signals
p.88
, any resolutions not
supported by this projector (XGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, it is recommended that the computer’s
external output should be set to XGA resolution.
With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
If no signal is being input from the connected equipment or signal input is stopped while
projecting, the “No signal” will appear.
If a signal not supported by the projector is input, the “Unsupport signal” will appear.
If an unavailable operation button is pressed, the
icon will appear.
1
2
1
2
1
2
3
1
Turn on the power.
Tu rn on the power by following the instructions in Turning the power on
p.26
.
The Easy setup function works to automatically adjust the screen focus and correct the
keystone distortion. If RGB signals are input, auto-setting is also made. This operation
does not take place when [Easy setup] in the Default setting menu is [Off]
p.44
.
2
Select the language and the lamp power (When using the
first time).
When the projector is used for the first time after purchase, the start menu for lan-
guage (to display the menus and messages on the screen) and lamp power selection
and configuration is displayed in English. (If the screen is out of focus, adjust it
according to the step
6
.)
q Use the or
button to select the
desired language and press the
button.
Message for setup confirmation is displayed in a
selected language.
Then, the menu for lamp power selection and
configuration is displayed. It is automatically set as
Standard. To change the setting, follow the step w.
w Use the
or
button to select the lamp
power and press the
button.
The lamp power, if selected, will be toggled without
pressing the
button. The display automatically
disappears in a few seconds.
Notes
When the projector is turned on the next time, the start menu does not appear upon
startup. However, if [Reset all] is executed from the Default setting menu
p.44
, the
start menu will be displayed the next time when the power is turned on.
The language can also be set via the Display setting menu
p.41
and Lamp power
via the Default setting menu
p.44
.
This owner’s manual assumes that English has been selected.
3
Activate the connected device.
Tu rn on and start the connected device such as a computer.
4
Press the INPUT button.
An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.
Notes
When [Auto input search] is set to [On] in the Default setting menu
p.44
(factory
setting is [On]), the input is switched to the connected equipment that is outputting video
signals each time you press the INPUT button
p.45
.
If no signal is being output from the connected equipment, pressing the INPUT button
does not change the input and “There is no other input signal. will appear.
Basic operations
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Tur kish
Polish
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
Control panel
Remote
Control
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba tdp tw355 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba tdp tw355 in the language / languages: English as an attachment in your email.

The manual is 9,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info