214450
23
Zoom out
Zoom in
Previous page
1/47
Next page
45
Operations
44
[Auto input search]
[On]: Automatically searches the signals that can be
projected, and switches input from the connected device
that outputs the signals each time the INPUT button is
pressed. The input from the connected device that
outputs no signals is skipped.
[Off]: Displays the Input select menu.
Toggle with
buttons and press button. (The
input without signals can be selected.)
[Power on]
Note that if [Power on] is set to [Auto], then if the main power
switch is ON when power is restored after a power outage, the
projector will come on.
[Easy setup]
<Auto keystone>: Switches on/off the automatic keystone distortion correction when the
EASY SETUP button is pressed or when Power on Easy setup is set to ON.
<Auto-setting>: Switches on/off the auto-setting function when the EASY SETUP button
is pressed or when Power on Easy setup is set to ON.
<Power on Easy setup>: Switches on/off the Easy setup operation when the power is
turned on.
Note
The Easy setup automatically switches off when [Ceiling] or [Rear ceiling] is selected
for projection mode.
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling
fan noise gets quieter.
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the
projector, for example, at high altitude (over 1,500 meters above sea level).
[Wireless standby]
When [Wireless standby] is set to [On], the wireless LAN is switched to the standby state
as the projector enters standby. While the wireless LAN is in standby, the projector can be
powered on using the remote control function of the Wireless Utility.
When [Wireless standby] is set to [Off], the projector cannot be powered on with the
remote control function of the Wireless Utility.
[Remote control]
Sets a remote control code from 4 types. You can set each code respectively for up to 4
projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
•You cannot operate the remote control if the codes of the projector and the remote
control do not match.
Remote control code setting for remote control
Remove the battery cover and set the same remote control code
switch as the projector.
p.16
(Use a screwdriver with thin tip to set.)
[Key lock]
Protect from operating errors by locking on the control panel buttons of the projector.
(The remote control operations are available.)
Control panel operations are locked after the setting is done.
•To release the key lock, press the control panel’s RETURN button for 10 seconds. The
key lock is released with a beep sound.
Computer 1 (Digital)
Y/P
B/PR 1 (Digital)
Computer 1 (Analog)
Y/P
B/PR 1 (Analog)
Computer 2
Y/P
B/PR 2
Computer 3
Y/P
B/PR 3
Video
S-video
Wireless / Card
USB memory
Input select
/ shows whether signal is
input or not.
Input select menu
Using the menus (Continued)
The default setting menu
This menu shows placement status and other settings.
Sets projection mode in accordance with Placement Style.
When projecting on a non-screen surface, select a color in accordance
with the projecting surface.
Press and switch with and .
Off/Green/Black/Brown/Blue/Beige
Set the time to wait for the power to be turned off after the last
operation is made with no input signal.
Press and switch with and .
Off (not turned off)/1 min./5 min./10 min./30 min./60 min.
Set whether the input with signals is only selected or not.
Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual Auto
Set the items of Easy setup and power ON/OFF.
[ or : Enter setting mode] [ : Select item] [On Off]
Auto focus
Auto keystone
Auto-setting
Power on Easy setup
Sets the lamp power.
Sets the cooling fan speed.
Switch on/off the wireless LAN while the projector is in standby.
When two or more projectors are used and controlled by the remote
control respectively, this menu sets the code for the projector and the
remote control.
[ or : Enter setting mode] [ : Select item] [ :
Select from 1, 2, 3, 4] [ :Confirm] [ :Select OK to end]
Press [Cancel] to return.
Lock the control panel buttons.
[ or : Enter setting mode] [ : Select item] [ :
Select On/Off] [ :Confirm] [ :Select OK to end]
Press [Cancel] to return.
Press . (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Password function
When [Password] is [On], the Password Setting screen is displayed.
Description
(Rear
ceiling)
(Standard)
(Rear) (Ceiling)
On Off
Wireless standby
Item
Projection
mode
Blackboard
mode
No signal
power off
Auto input
search
Power on
Easy setup
Lamp power
Fan mode
Remote control
Key lock
Reset all
Password
Low Standard
Standard High
Yes No
Off On
On Off
p.22
p.36
On Off
On
On Off
On Off
Detailed description
[Blackboard mode]
Projects the image in colors more like projecting on a screen.
Precaution
The projected image may differ depending on the type, color, and material of the
blackboard and wall even if the selected color is the same as the projected screen.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba tdp tw300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba tdp tw300 in the language / languages: English as an attachment in your email.

The manual is 6,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info