485559
25
Zoom out
Zoom in
Previous page
1/31
Next page
48 49
Maintenance
The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure
to fully understand the following characteristics of the lamp and handle it with extreme care.
The lamp may burst with a loud noise due to impact or deterioration, or fail to light at
the expiration of its life.
•How long it takes before the lamp bursts or the life expires may vary greatly by lamp.
Some may burst shortly after first use.
Burst is likely to happen if the lamp is used after the replacement period has elapsed.
When the lamp bursts, the broken pieces of glass may get inside the product or be
released outside from the openings for ventilation.
When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with
glass dust may be released from the openings for ventilation.
Immediately replace the lamp when a sign appears on the screen.
When the replacement time approaches, a message will appear on the screen.
The risk of burst will increase if the lamp is continuously used without being replaced.
•Frequently check the used hours and prepare spares when the replacement time
approaches. (Refer to “Status display”.
p.48
)
When the lamp is broken
If glass components, including a lamp and a lens, should break, handle the broken
pieces with care to avoid injury and contact your dealer for repair service.
In the event of lamp burst, unplug the product from the wall outlet, leave and completely
ventilate the room. Then, thoroughly clean the area around the projector and discard
any edible items placed in that area.
When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes
or you breathe it.
Lamp replacement
A lamp is consumable supplies. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime
of the lamp depends on condition of use.) If this happens, replace it with a new one
.
WARNING
If the projector is mounted on the ceiling, it is recommended to use your Toshiba dealership
when the lamp has to be exchanged.
Uncovering the lamp while the projector is mounted on a ceiling may lead to a danger
of damage from falling pieces of glass if the lamp is broken. Besides, working at high
elevations can also be hazardous. Do not attempt to replace the lamp by yourself.
When replacing, always use lamp “TLPLW13” (sold separately).
CAUTION
If you have been using the projector, the lamp will be very hot, and may cause burn injuries
.
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
If the lamp should break, please handle with care to avoid injury due to broken pieces and
contact your dealer for repair service.
About lamp
Maintenance
Using the menus (Continued)
Displaying Information (Status display)
This displays information about the input signal, lamp use time, LAN connection status,
etc.
“Yes”: displayed, “No”: not displayed
Item Description
Computer Y/PB/PR Video S-video
Projector
Input Input source name Yes Yes Yes Yes
Mode name RGB input mode
[Note 1]
Ye s N o N o N o
Resolution Resolution (in dots) Yes No No No
Frequency Sync frequency Yes No No No
Sync Sync signal polarity
[Note 2]
Ye s N o N o N o
Signal format Y/P
B
/P
R
signal format No Yes No No
Video mode Color method of video signal No No Yes Yes
Lamp time Time of lamp use
[Note 3]
Ye s Ye s Ye s Ye s
Lamp reset count The count for lamp replacement Yes Yes Yes Yes
Total time The total time that this projector is
used.
Ye s Ye s Ye s Ye s
Version Firmware version
[Note 4]
Ye s Ye s Ye s Ye s
Wired LAN
Connection status Displays connection status of LAN. Yes Yes Yes Yes
IP address Displays the IP address. Yes Yes Yes Yes
Subnet mask Displays numeric value of subnet
mask.
Ye s Ye s Ye s Ye s
Gateway Displays numeric value of gateway. Yes Yes Yes Yes
MAC address Displays MAC address of the
projector.
[Note 5]
Ye s Ye s Ye s Ye s
PJLink class PJLink version Yes Yes Yes Yes
Notes
1: The mode of supported RGB signals
p.56
is shown.
2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 1,500 hours, consult
with a store about getting a TLPLW13 replacement lamp (sold separately) prepared.
4: [Version] shows the version of the projector’s internal control program. This version is referred
to for customer service, etc.
5: In case that “------” appears for MAC address, please contact your dealer.
Note
The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again. The information regarding
wired LAN is refreshed every time it is displayed.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba TDP-T350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba TDP-T350 in the language / languages: English as an attachment in your email.

The manual is 9,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info