485551
17
Zoom out
Zoom in
Previous page
1/25
Next page
33
Operations
32
Using the menu (Continued)
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item Description
Computer Y/PB/PR
Video
Camera
S-video
Input Input source name Yes Yes Yes Yes
Mode name RGB input mode
[Note 1]
Yes No No No
H-resolution Horizontal resolution (in dots) Yes No No No
V-resolution Vertical resolution (in dots) Yes No No No
H-frequency Horizontal sync frequency Yes No No No
V-frequency Vertical sync frequency
[Note 2]
Yes No No N o
Sync Sync signal polarity
[Note 3]
Yes No No N o
Signal format Y/PB/PR signal format No Yes No No
Video mode Color method of video signal No No Yes No
Lamp time Time of lamp use
[Note 4]
Yes Yes Yes Yes
Lamp reset count The count for lamp replacement Yes Yes Yes Yes
Total time
The total time that this projector is used
Yes Yes Yes Yes
Version Firmware version
[Note 5]
Yes Yes Yes Yes
Notes
1: The mode of supported RGB signals
p.45
is shown.
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 3,000 hours, consult
with a store about getting a TLPLV4 replacement lamp (sold separately) prepared.
5: [Version] shows the version of the projectors internal control program. This version is referred
to for customer service, etc.
Note
The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
The default setting menu
This menu shows placement status and other settings.
Sets projection mode in accordance with Placement Style.
Set the timer to wait for the power to be turned off after signal input stops.
Press . Switch with and .
Off (not turned off)/1 min./5 min./10 min./30 min./60 min.
Set whether the input with signals is only selected or not.
Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual Auto
Sets the lamp power.
Sets the cooling fan speed.
Press .
Resets all adjustments and settings to their factory settings.
Description
Item
Projection
mode
No signal
power off
Auto input
search
Power on
Lamp power
[Note 1]
Fan mode
[Note 2]
Reset all
(Rear mounted
from ceiling)
(Standard)
(Rear)
(Mounted
from ceiling)
On Off
Standard High
Yes No
Low Standard
p.20
Notes
1: When Lamp power is set to Low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off.
2: Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the projector,
for example, at high altitude (over 1,500 meters above sea level).
Notes
Note that in the event of a power outage but the power is restored afterwards, the projector
power will come on if Power on is set to Auto, and the power cord is plugged in.
When you turn off the projector even if Power on is set to Auto, you must press the ON/
STANDBY button to turn the power off.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba TDP-S20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba TDP-S20 in the language / languages: English as an attachment in your email.

The manual is 6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info