214662
23
Zoom out
Zoom in
Previous page
1/50
Next page
44 45
Operations
Using the menus 1 (Continued)
Default setting 2 menu
Item
Description
Projection
mode
Sets projection mode in accordance with Placement Style.
p.23
(Standard)
(Rear)
(Ceiling)
(Rear ceiling)
Fan mode Sets the cooling fan speed. Standard
High
Remote control When 2 projectors are used and controlled by the remote control respectively,
this menu sets the code for the projector and the remote control.
[
or : Enter setting] [
: Select from 1, 2
] [ : Confirm]
[
:Select OK to end
]
Press [Cancel] to return.
Key lock Lock the control panel buttons.
[
or : Enter setting] [
: Select On/Off
] [ : Confirm]
[
:Select OK to end
]
Press [Cancel] to return.
Lamp power
Set the lamp power. Low
Standard
Reset all
Press
. (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings. Yes
No
Password
Password setting
p.35
Press . Password registration/Password setting
Detailed description
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise
gets louder.) Set this option to use the projector, for example, at high altitude (over 1,500
meters above sea level).
Do not set Fan mode to [High] when using the projector at a lower altitude.
[Remote control]
Sets a remote control code from 2 types. You can set each code respectively for up to
2 projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
You cannot operate the remote control if the codes of the projector and the remote
control do not match.
Remote control code setting for remote control
Set the same remote control code switch as the projector.
p.18
p.19
[Key lock]
Protect from operating errors by locking on the control panel buttons of the projector.
(The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly operation
with the control panel buttons is disabled.
To release the key lock, set the [Key lock] to [Off] using remote control. Pressing
the [RETURN] button on the projector for 10 seconds also sets the [Key lock] to [Off].
(When operating the main unit, the 2 indicators of LAMP and TEMP light in orange
for 3 seconds, and at the same time the projector beeps.) However, when Network
or USB memory input is selected, the [Key lock] cannot be set to [Off] with the
[RETURN] button on the projector.
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling
fan noise gets quieter.
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item Description Computer
Y/PB/PR
Video S-video
Network
USB
memory
Input Input source name Yes Yes Yes Yes Yes Yes
Mode name RGB input mode
[Note 1]
Yes NoNoNoNoNo
Resolution Resolution (in dots) Yes No No No No No
Frequency Sync frequency Yes No No No No No
Sync Sync signal polarity
[Note 2]
Yes NoNoNoNoNo
Signal format Y/P
B/PR signal format No Yes No No No No
Video mode Color method of video signal No No Yes Yes No No
Lamp time Time of lamp use
[Note 3]
Ye s Ye s Ye s Ye s Ye s Ye s
Lamp reset count The count for lamp replacement Yes Yes Yes Yes Yes Yes
Total time
The total time that this projector is
used.
Ye s Ye s Ye s Ye s Ye s Ye s
Version Firmware version
[Note 4]
Ye s Ye s Ye s Ye s Ye s Ye s
Notes
1: The mode of supported RGB signals
p.94
is shown.
2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot
be used as a counter of guaranteed lamp time.) When the displayed time approaches
2,000 hours, consult with a dealer about getting replacement for:
TLPLW15 for TDP-EW25 (sold separately).
4: [Version] shows the version of the projector’s internal control program. This version
is referred to for customer service, etc.
Note
The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
N
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba tdp ew25 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba tdp ew25 in the language / languages: English as an attachment in your email.

The manual is 4,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info