562486
68
Zoom out
Zoom in
Previous page
1/76
Next page
68
Chapter 5
Troubleshooting
General troubleshooting
Before calling a service technician, review this chapter for possible causes/solutions for the problem you are experiencing.
Before you begin to troubleshoot any problem, rst unplug the monitor from the AC wall outlet, wait approximately one
minute, and then plug the monitor back into the AC wall outlet. If the problem still exists attempt to troubleshoot the
problem.
No picture
The signal cable should be securely connected to the display card/computer.
The display card should be securely seated in its slot.
The Main Power Switch and the computer power switch should be in the ON position.
Make sure that the correct mode has been selected on the display card or system being used.
(Please consult the display card or system manual to change the graphics mode.)
Check the monitor and your display card with respect to the compatibility and recommended settings.
Check the signal cable connectors for bent or pushed-in pins.
Power button does not respond
Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.
Image persistence
Please be aware that LCD Technology may experience a phenomenon known as “image persistence.” Image
persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT
monitors, LCD displays’ image persistence is not permanent, but constant images being displayed for a long period of
time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was
displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should
be turned off for one hour to erase the image.
As with all display devices, recommends displaying moving images and using a moving screen saver at regular
intervals whenever the screen is idle or turning off the monitor when not in use.
Image is unstable, unfocused or swimming is apparent
Signal cable should be securely attached to the computer.
Use the OSD Image Adjust controls to focus and adjust the display by increasing or decreasing the ne adjustment.
When the display mode is changed, the OSD Image Adjust settings may need to be re-adjusted.
Check the monitor and your display card with respect to the compatibility and recommended signal timings.
If the displayed text is garbled, change the video mode to the non-interlace mode and use 60 Hz refresh rate.
Image of component signal is greenish
Check to see if the YPbPr input connector is selected.
LED on the monitor is not lit (No green or red color can be seen)
Power Switch should be in the ON position and power cord should be connected.
Make certain the computer is not in the power-saving mode (touch the keyboard or mouse).
RED LED on the monitor is blinking
A certain failure may have occurred. Please contact your nearest authorized service facility.
Displayed image is not sized properly
Use the OSD Image Adjust controls to increase or decrease the coarse adjustment.
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba TD-Z471 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba TD-Z471 in the language / languages: English as an attachment in your email.

The manual is 19,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info