562486
65
Zoom out
Zoom in
Previous page
1/76
Next page
65
Other functions
Supplemental information of the auto brightness function
Audio input change
You can select the audio input using the AUDIO INPUT button.Note that the selectable audio inputs vary depending
on the currently selected video signal input.
Selection of the video signal input Operation
HDMI1 or HDMI2
DVI-D ANALOG only
D-SUB ANALOG only
OPTION**
PC (OPS-compliant
computer)
DISPLAYPORT
YPbPr
ANALOG only
S-VIDEO ANALOG only
VIDEO ANALOG only
* The audio of HDMI1 or HDMI2 being selected is output as the HDMI audio.
** OPTION can be used when an expansion module is mounted on the option slot.
Supplemental information of the auto brightness function
To control multiple monitors collectively
In such a case where the tiling function is used, you can control the auto brightness function by sharing the detection
result of the brightness sensor of a certain monitor among the connected monitors.
1 Multi-connect the monitors using RS-232C cables (commercially available) as shown by the example below.
Master: Monitor conf gured as Master that detects
the outside light (Monitor ID is “1”.)
Slave: Monitor controlled by the Master monitor
(Monitor ID is other than “1”.)
2 Assign a monitor ID to each multi-connected TD-Z421/ TD-Z471 using MONITOR ID. (See page 58.) Monitor ID is
selectable from 1 to 26. The monitor ID of the Master monitor should be “1” and those of the Slave monitors should
be other than “1”. You are recommended to assign IDs to the monitors consecutively from 1, 2, 3, and on.
3 Set AUTO BRIGHTNESS on the OSD screen (PICTURE) as follows.
AUTO BRIGHTNESS CONTROL
Master monitor LOCAL PRIMARY
Slave monitors REMOTE SECONDARY
To use a computer to control the monitors
When using a computer to control the monitors, you must prepare an application software program for control by
yourself. Brightness of all the monitors can be controlled centrally using a computer, if the customer create a control
application to remotely read the value from two brightness sensors of any monitor and distribute it to all monitors.
1 Connect the RS-232C IN connector of the Master monitor shown above and the RS-232C connector of the
computer using an RS-232C cable. The communication control function via LAN isn’t supported on the monitor
alone, however, it is available when the monitor is used with the computer.
Audio input change
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba TD-Z471 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba TD-Z471 in the language / languages: English as an attachment in your email.

The manual is 19,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info