465044
73
Zoom out
Zoom in
Previous page
1/80
Next page
73
EN
Introduction Connections
Basic Setup /
TV View Operation
Playback Editing OthersFunction SetupRecording FunctionsIntroduction Connections
Basic Setup /
TV View Operation
Playback Editing OthersFunction SetupRecording
Troubleshooting
Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing. Some
simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.
Others
Symptom Remedy
POWER
The power does not turn on. Check that the AC power cord is connected securely.
Batteries of the remote control are weak.
The unit turns on automatically without
any operation.
The unit turns on automatically 2 seconds before the timer recording.
GENERAL
The unit does not function. ” or error message appears if the operation is prohibited.
Batteries of the remote control are weak or exhausted.
No picture, sound or menu appears on
the screen.
Check if the connections are made securely and correctly.
Check if the cables are damaged.
Check if a correct external input channel is selected on your TV. (See page 19.)
Check if you have completed “Channel” setting. (See pages 20-22.)
“Clock” setting and “Channel” setting
cannot be performed.
If a recording is in progress, these operations cannot be performed.
The unit does not operate properly. Moisture has condensed inside the unit. Remove the disc and leave the unit
turned on for about 2 hours until the moisture evaporates. (See page 3.)
The clock display does not appear on
the front panel display.
Check that the AC power cord is connected securely.
(In case of power failure) Check the breaker and “Clock” setting.
When you forget the password for
parental lock.
Please cancel the password and the set level. (See page 67.)
DV signal cannot be input. Before connection, turn on the power supplies for both this unit and the DVC,
and make sure that these units have stopped.
Only a “DVC-SD” signal can be input from the DVC to this unit. Other types of
signals are not supported.
Do not connect any device other than the DVC. Even if a recorder or PC with
another DV terminal is connected, the DV function will not operate.
If the DVC is not recognised after connection, turn off the power supply for the
unit and re-connect the DVC.
The DVC cannot be operated with this
unit.
Signal input or DVC operation from this unit may be disabled depending on the
type of DVC.
If a DVC signal cannot be input, use an external input (AV2/AV3) for analogue
connection via audio/video cables. Use Scart adaptor for connecting to AV2.
DVC control may be disabled depending on the type of DVC, even in a mode
other than camera mode. In this case, switch to DVD control and execute the
normal recording procedure while operating the DVC.
Certain functions of the DVC cannot
operate.
Some functions may not operate depending on the type of DVC. For example, if
the DVC does not support slow playback mode, the slow playback function is
disabled.
With DV(AV4), the disc display menu does not appear unless disc playback is
executed.
DV audio signal cannot be switched. For recording with the DVC, the recording audio signal can be set to 12 bits or
16 bits. However, when 16-bit recording mode is selected, audio signal cannot
be switched. To record an audio signal, set it to 12 bits.
No image from HDMI connection. Check the HDMI connection. (Check the status of the HDMI related indications.)
Check whether the connected monitor device or other device supports HDCP.
(This unit will not output a video signal unless the other device supports HDCP.)
Check the setting of HDMI.
Check whether the output format of this unit (HDMI FORMAT) matches the
supported input format of other connected device.
If the unit is connected to the unauthorised display device with an HDMI cable,
the audio and video signals may not be output when playing back a commercial
DVD-video.
E2TC2BD_EN.book Page 73 Thursday, May 7, 2009 9:02 AM
73


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba RD99 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba RD99 in the language / languages: English as an attachment in your email.

The manual is 10,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info