497489
47
Zoom out
Zoom in
Previous page
1/59
Next page
47
Horizontal grille
Screw
Louver
motor
Hooks
Pipe holder
Hooks fixing the
heat exchanger
Shaft bearing
base
Screw fixing the
heat exchanger
Hook
Screw
Cross
Cross
flow fan
flow fan
Rear plate
6~7mm
Cross
flow fan
Shaft
bearing
base
Mount the fan motor
as shown in figure
in the left when
assembling.
Put the end of lead
wire at the portion
between two ribs.
Ribs
Ribs
Ribs
No. Part name Procedure Remarks
T
Horizontal
g
rille
Note:
The horizontal
grille can not be
removed without
removing the
louver motor.
1) Perform the process
R
.
2) Remove the screw fixing the louver motor, and
remove the louver motor.
3) Remove the shaft of the horizontal grille from the
drain-pan.
U
Heat exchan
g
er 1) Perform the process
S
.
2) Remove the pipe holder from the rear side of main
unit by removing the screw.
3) Unhook the hooks fixing the left side of the heat
exchanger and remove the screw fixing it, then
remove the right side of the end plate from the rib
fixing the main unit by sliding the heat exchanger
slightly to the right side.
V
Cross flow fan 1) Perform the process
S
.
2) Loosen the set screw of the cross flow fan.
3) Remove the screw fixing the shaft bearing base.
4) Lift slightly up the left side of the heat exchanger, and
pull the shaft bearing base out left downwards.
When assembling it, fix it with the set screw on the
position where the gap between the rear plate surface
and the left end surface of the cross flow fan is 6 ~ 7mm.
W
Shaft bearing 1) Perform the process
V
above.
2) Remove the shaft bearing from the shaft bearing
base.
<Caution for assembling>
If a part of the shaft bearing is protruded from the
housing, assemble it after pushing its portion into the
correct position in the housing.
X
Fan motor 1) Perform the process
U
above.
2) Perform the process
V
-2) above.
3) Remove the left and right motor bands.
4) Remove the fan motor after pulling the cross flow fan
out sliding it left and right.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba RAS-07YK-E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba RAS-07YK-E in the language / languages: English as an attachment in your email.

The manual is 10,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info