215056
56
Zoom out
Zoom in
Previous page
1/64
Next page
E-55
Troubleshooting
Check the following matters before requesting servicing.
Is the power cord plugged into a power outlet?
Is the lamp cover properly mounted?
Is the projector’s temperature high? To protect the projector, the power can-
not be turned on when the projector’s temperature is abnormally high.
Has the lamp reached the end of its service life?
Is a connected input selected?
Is the cable properly connected to the input terminal?
•When a computer is connected, are signals being output from the computer?
Does the signal being input have a frequency usable with this projector?
Are the brightness and contrast adjusted to the minimum?
Is the STATUS indicator lit a steady red or flashing red?
When the component signal of the DVD player is connected with the RGB
connector and the image is not output, is [Input Settings] of the RGB con-
nector properly selected?
For a RGB input, has the picture been properly adjusted?
Is the projector properly installed?
For trapezoidal (keystone) distortion, perform keystone adjustment.
Please note that depending on the projected picture and the projection con-
ditions, it may not be possible to eliminate keystone distortion completely.
Is the lens properly focused?
Are the screen and projector installed at the proper distance?
Does the projection distance exceed the focusing range?
Is there condensation on the lens, etc.?
If the projector is moved from a cool storage area to a warm place and the
power is turned on, condensation may form on the lens or internal optical
parts. If this happens, wait until the condensation has evaporated before
using the projector.
For a computer input, are the horizontal and vertical positions properly ad-
justed?
Does the input signal have a compatible resolution and frequency? Check
the computer’s resolution.
If the image is crushed in the horizontal or vertical direction or if it is not
displayed over the entire screen, select a different aspect ratio.
When a component signal is being input, is the color space setting proper?
For a composite input, is the tint properly adjusted?
From the menu, select “Image” and adjust the clock frequency and phase.
Other than [Settings], [Option] and [Information], selection will not be pos-
sible unless a signal is being input to the projector and the image/picture is
projected.
Are the remote control unit’s batteries worn? Replace with new batteries.
Is there an obstacle between the remote control unit and the projector’s
remote control signal sensor?
Is the remote control unit outside of range?
Are you pointing the remote control unit’s transmitter towards the projector’s
remote control signal sensor?
See “When an indicator is lit or flashing”.
Power does not turn on
No image is produced
Image is distorted
Image is out of focus
Image is not in proper po-
sition and is not displayed
properly
Video image is crushed
Colors of the overall image
are strange
Characters flicker or colors
are offset for RGB inputs
Cannot select the menu
name
Remote control unit does
not operate
STATUS indicator is lit red
or flashing red
Problem
Check
Reference
Page
E-19
E-59
E-54
E-54
E-24
E-1417
E-53
E-61
E-40
E-54
E-49
E-40, 41
E-23
E-27, 46
E-22
E-13
E-13
E-41
E-61
E-25
E-43
E-40
E-40, 41
E-11
E-11
E-11
E-11
E-54
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba p7 dlp projector at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba p7 dlp projector in the language / languages: English as an attachment in your email.

The manual is 2,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info