485545
15
Zoom out
Zoom in
Previous page
1/42
Next page
15
SETTING UP
Setting up screen
Set the screen perpendicular to the projector. If the screen can not be set perpendicularly, adjust the
projection angle of the projector. (See below.)
Adjust the screen or projector so that the shadow of the projector lens may be projected onto the center of the
screen.
Do not place the screen where the direct sunlight and illuminating lights come onto the screen. Direct light
illumination onto the screen could whiten the screen surface making the projected picture images bad to see.
Basic setup
Determine the distance from the screen to the projector according to the size of the picture images to be
projected. (See Page 14 and 15.)
Screen
Size of projected picture
images (Width)
A
A=B
B
Screen
Projector
As for the locations for the setup, read "Be sure to observe the followings for safety" described on Pages 4 to 7
in advance.
Adjusting projection angle
If a part of the projected picture image lies off the
edge of the screen, adjust the projection height or
the projection angle as follows:
1. Lift up the projector up to the desired projection
angle by hands.
Set the projector within a tilt angle of 15 degrees.
2. Press up the left and right angle adjusting buttons.
3. Release the hands from the angle adjusting but-
tons and projector.
5. Slowly lift down the projector by pressing the left
and right angle-adjusting buttons while holding the
projector by hands.
It is also possible to adjust the projection angle by turn-
ing the angle adjusting foot (rear) to the lift or right.
If the projected image frame is distorted
to a trapezoid:
If the screen and the projector are not set perpen-
dicular to each other, the projected image frame be-
comes trapezoidal.If it is not possible to bring them
into positions perpendicular to each other by any
mechanical adjustments, adjust the value for trapezoi-
dal correction in the setup menu. (See Page 19.)
If the "trapezoidal correction" is applied, the as-
pect ratio may not be adjusted correctly in some
cases.
If the "trapezoidal correction" is applied, the reso-
lution of the projected image will be reduced. Also,
moire fringes on fine-pattern images or drooping
of straight lines in the images will appear. There-
fore, try to set the screen and the projector per-
pendicular to each other as much as possible.
12
4. By turning the angle adjusting foot (front) to the
left or right, make fine adjustment so that the pro-
jected image frame may be in parallel with the
sides of the screen.
When storing the projector:
4
5
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba MT500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba MT500 in the language / languages: English as an attachment in your email.

The manual is 2,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info