587680
32
Zoom out
Zoom in
Previous page
1/81
Next page
29
When address setup has finished in all the systems, turn
off SW30-2 on the interface P.C. boards of the lines
connected to the identical central control except a line
with least line address number.
(Terminator resistors of the wires in the central control
line of indoor/outdoor are unified.)
Connect the relay connector between [U1U2] and [U3U4]
terminals of the outdoor unit for each refrigerant line.
Then set up the central control address.
(For the central control address setup, refer to the Instal-
lation manual of the central control devices.)
Interface P.C. board
SW11
1
ON
2 3 4
SW12
1
ON
2 3 4
SW06
1
ON
2 3 4
SW07
1
ON ONON ON
2 3 4
SW09SW08
11 2 3 4
SW10
1 2 3 4
SW13
1
ON
2 3 4
SW14
1
ON
2 3 4
SW30
SW30
1
ON
2
SW04
SW01
1
SW05 SW15
D600 D601 D602 D603 D604
1 1
SW02 SW03
SW15
7-segment
display
Switch setup
(Example in case of central control over refrigerant system)
Outdoor side (Manual setup)
* Manual setup is necessary for column of which letter color is reversed.
CAUTION
For relay connector
Never connect a relay connector until address setup for all the refrigerant systems finishes;
otherwise address cannot be correctly set up.
U3 U4
U1 U2
U1 U2
A B
Outdoor unit
Individual
Central
remote controller
Group
Remote
controller
U1 U2
A B
Remote
controller
U1 U2
A B
Outdoor unit
Remote
controller
U1 U2
A B
U1 U2
A B
Outdoor unit
Remote
controller
Relay
connector
U3 U4 U3 U4
U1 U2
Relay
connector
U3 U4
U1 U2
Relay
connector
Line address
Indoor unit address
Group address
Indoor side
(Automatic setup)
Outdoor interface
P.C. board
Setup at shipment
from factory
SW13, 14
(Line address)
Relay connector
Outdoor unit Outdoor unit
Open
OFF after
address setup
Short after
address setup
Short after
address setup
ON
1
ON
12
Outdoor unit
OFF after
address setup
Short after
address setup
3
SW30-2
Terminator resistor of
indoor/outdoor communi
cation line/central control
communication line
1
1
0
1
2
0
2
1
1
2
2
2
3
1
0
6
ADDRESS SETUP
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba MCY-MAP0401HT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba MCY-MAP0401HT in the language / languages: English, German as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info