Manual Toshiba lcd data projector tlp x2500a (page 23 of 31) (English)

215050

Zoom out

Zoom in

1/31

Operations

Using the menus (Continued)

[Key lock]

Protect from operating errors by locking on the control panel buttons of the

projector. (The remote control operations are available.)

Control panel operations are locked after the setting is done, and accordingly

operation with the control panel buttons is disabled.

•To release the key lock, set the [Key Lock] to [Off] using remote control. Pressing

the [RETURN] button on the projector for 10 seconds also sets the [Key Lock] to

[Off]. (When operating the main unit, the 2 indicators of LAMP and TEMP light in

orange for 3 seconds, and at the same time the projector beeps.)

■ Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

“Yes”: displayed, “No”: not displayed

Item Description

Computer Y/PB/PR Video S-video

Camera

(XC2500)

Projector

Input Input source name Yes Yes Yes Yes Yes

Mode name RGB input mode

[Note 1]

Ye s N o N oNo No

Resolution Resolution (in dots) Yes No No No No

Frequency Sync frequency Yes No No No No

Sync Sync signal polarity

[Note 2]

Ye s N o N oNo No

Signal format Y/P

signal format No Yes No No No

Video mode Color method of video signal No No Yes Yes No

Lamp time Time of lamp use

[Note 3]

Ye s Ye s Ye s Ye s Ye s

Lamp reset count The count for lamp replacement Yes Yes Yes Yes Yes

Total time The total time that this projector

is used.

Ye s Ye s Ye s Ye s Ye s

Version Firmware version

[Note 4]

Ye s Ye s Ye s Ye s Ye s

Notes

1: The mode of supported RGB signals

p.57

is shown.

2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].

3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as

a counter of guaranteed lamp time.) Please replace the lamp after 2000 hours of use if [Lamp

power] is set to [Standard], or after 3000 hours of use if [Lamp power] is set to [Low], consult

with a dealer about getting replacement for lamp TLPLW11 (sold separately).

4: [Version] shows the version of the projector’s internal control program. This version is referred

to for customer service, etc.

Note

• The displayed information will not be refreshed if the status changes. To refresh the

information, dismiss the display, then display it again.

Please read this chapter if the model you purchased includes a document camera.

■ Preparation of the document camera

1) Setup the arm

Status before preparation

(When stored)

3) Let the camera lens face below

2) Raise the camera head

4) Let the camera lens face the object

PRECAUTIONS

• Do not jolt or force the camera head or camera arm. Doing so could cause malfunction.

• The CMOS image sensor mounted on the camera of this projector is produced by

precision engineering. Please be informed that missing pixels and bright spots are not

considered as problems.

Note

• It takes about 10 seconds from when the power is turned on until the operation is

possible. This is not a problem.

Using the document camera

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba lcd data projector tlp x2500a in the language / languages: English as an attachment in your email.

The manual is 5,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toshiba lcd data projector tlp x2500a Manual

Product: