Manual Toshiba HDR5010 (page 4 of 48) (English)

560961

Zoom out

Zoom in

1/48

Digital TV recorder

HDR5010KB

OWNER’S MANUAL

HDR5010 User Guide.indb 1 22/07/2010 10:38

Introduction

Important Safety Information

Thank you for choosing this Toshiba Digital TV recorder.

Before using the Digital TV recorder, please take a minute to read the following important

safety information.

•Although this appliance has been

carefully manufactured and rigorously

checked prior to leaving the factory, as

with all electrical appliances it is possible

for problems to develop. If you notice

smoke, an excessive build-up of heat

or any other unexpected phenomena,

you should disconnect the plug from the

mains power socket immediately.

•Ensurethattheunitissufciently

ventilated! Never place next to or

underneath curtains!

•Only use the supplied AC mains adapter.

•This AC mains adapter should only be

connected to an AC 230V/50Hz mains

power supply - do not attempt to connect

it to any other type of supply.

•The socket-outlet must be installed near

the equipment and easily accessible.

•DO NOT cut off the supplied AC mains

adapter’s plug.

•Always hold the plug when pulling it out

from the power mains supply system.

DO NOTpullonex.Theexcan

become overloaded and cause a short

cut.

•Set up unit so that no one is able to trip

overtheex.

•This unit is recommended to be installed

on shock-free benches in order to avoid

any danger from falling.

•DO NOT use the unit near heat sources.

Thecasingandexcouldbedamaged

by the effect of heat.

•Any repairs must be carried out by

qualiedservicepersonnelonly.

•DO NOT open this unit. If you are in

doubt about it working normally, switch

off, unplug the AC mains adapter and

consult your dealer.

•Avoid placing the unit on any surfaces

that may be subject to vibrations or

shocks.

•Leave a space of at least 10cm around

the unit to allow for adequate ventilation.

•Place the unit on a stable surface.

•DO NOT place any magnetic objects

(including speakers) on or near the unit.

•DO NOT place any objects on the unit.

•DO NOT obstruct the ventilation on the

underside of the unit.

•DO NOT expose the unit to shocks or

vibrations as this could cause Hard disk

drive damage.

•To protect the unit during a thunder

storm unplug the AC power cord and

disconnect the aerial.

•CAUTION: DO NOT touch the aerial

connector.

•When you leave your home for a long

period of time, unplug the AC mains

adapter for safety reasons.

HDR5010 User Guide.indb 2 22/07/2010 10:38

Introduction

Important Safety Information

•The unit becomes warm under normal

operation. DO NOT place any covers or

blankets on the unit in order to prevent

overheating. The ventilation holes are not

to be blocked.

DO NOT set up near radiators.

DO NOT place in direct sunshine.

•DO NOT allow the unit to get wet.

•DO NOT use the unit in hot, humid or

excessively dusty places.

•DO NOT expose the unit to rain or

moisture.

•The apparatus shall not be exposed to

dripping or splashing and that no objects

lledwithliquids,suchasvases,shallbe

placed on the apparatus.

•Liquids spilled into the unit can cause

serious damage. Switch the set OFF and

disconnect the AC mains adapter, then

consultaqualiedservicepersonbefore

attempting to use the unit again.

•Moisture condensation occurs, for

example, when you pour a cold drink

into a glass on a warm day. Drops of

water form on the outside of the glass. In

the same way, moisture may condense

inside this unit.

DO NOT use the unit when moisture

condensation may occur.

If you use the unit in such a situation,

it may damage the Hard disk drive and

internal parts. Leave the unit for two or

three hours.

•To clean the unit, use a lightly dampened,

soft cloth. DO NOT use any kind of

abrasive cloth, sponge or cleaner.

•To help prevent Screen burn on Plasma

or LCD screens and CRT displays. Never

leave static pictures on the screen for

long periods of time.

•Neverplacehotobjectsofopename

sources, such as lighted candles or night

lights, on or close to the unit.

•High temperatures can melt plastic and

leadtores.

•DO NOT stand the unit vertically. Use the

unitinahorizontal(at)positiononly.

•The AC mains adapter is used as a

disconnecting device and therefore

should be readily operable.

•WARNING: To prevent the

spreadofre,keepcandles

orotheropenamesaway

from this product at all times.

HDR5010 User Guide.indb 3 22/07/2010 10:38

Introduction

General Information

Toshiba is not liable for any damage or loss caused directly or indirectly by the malfunction

of this unit, including, without limitation, any one of the following:

•Failure to record contents intended to be recorded by the consumer.

•Failure to edit contents as intended by the consumer.

Note:

• In the event your product is returned to our service centre, we are unable to guarantee your recordings will be

maintained.

Hard Disk Drive (HDD) Handling

The HDD is a precision apparatus that is susceptible to vibration, strong impact or dirt.

Depending on the installation environment or handling, the unit may become partially

damaged or in the worst case, recording or replaying may not be available. Especially while

the HDD is in motion, do not subject it to vibration or strong impact or pull out the power plug.

And if a power failure occurs, the content of the recording / replaying programme may be lost.

HDD rotates at high speed when in operation. Be sure that rotation has stopped and then

move the unit without subjecting it to strong impact or vibration.

We do not assume any liability for losses caused by misuse or malfunction.

About HDD

The HDD is a special device which has high recording density and is suited for long-time

recording or high-speed cueing but by contrast, has many factors which can cause breakage.

•When an HDD fails, recovery of recorded content (data) may be impossible.

•The HDD is not a permanent storage location of the recorded contents.

About the remaining capacity of HDD recording time:

In recording to the HDD, the Remaining Capacity Display may differ from the actual

recordable time as this unit adopts Variable Bit Rate encoding, which varies the recording

(storage) amount of data in conformity with the amount of information in the video signal.

BeforerecordingtotheHDD,ensurethereissufcientspaceontheHDDbydeleting

unnecessary titles in advance.

Notes on Copyright

About Copyright

Unauthorised copying, broadcasting, public performance and lending of discs are

prohibited. This product incorporates copyright protection technology that is protected

by U.S. patents and other intellectual property rights. Use of this copyright protection

technology must be authorised by Rovi Corporation, and is intended for home and other

limited viewing uses only unless otherwise authorised by Rovi Corporation. Reverse

engineering or disassembly is prohibited.

HDR5010 User Guide.indb 4 22/07/2010 10:38

Introduction

Notes on Copyright

ToplaybackhighdenitionvideoimagesviaanHDMIconnection,itisnecessarythat

boththeplayerandthedisplaydevice(oranAVamplier)supportacopyrightprotection

system called HDCP (high-bandwidth digital content protection system).

•HDCP is copy protection technology that comprises data encryption and authentication

of the connected AV device.

•This unit supports HDCP.

•Pleasereadtheoperatinginstructionsofyourdisplaydevice(orAVamplier)formore

information.

•Because HDMI is an evolving technology, it is possible that some devices with an HDMI

input may not operate properly with this unit.

•When using an HDCP-incompatible display device, the image will not be viewed properly.

•When power failure occurs or when you unplug the unit, HDMI settings may change.

Please check and set the HDMI settings again.

*HDMI:HighDenitionMultimediaInterface

Environmental Information

Following information is only for EU-member states:

The use of the symbol indicates that this product may not be treated as household

waste. By ensuring this product is disposed of correctly, you will help prevent potential

negative consequences for the environment and human health, which could otherwise

be caused by inappropriate waste handling of this product. For more detailed information

aboutrecyclingofthisproduct,pleasecontactyourlocalcityofce,yourhousehold

waste disposal service or the shop where you purchased the product.

Disposal of batteries and/or accumulators

The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators

must be collected and disposed of separately from household waste.

Ifthebatteryoraccumulatorcontainsmorethanthespeciedvaluesoflead(Pb),

mercury(Hg),and/orcadmium(Cd)denedintheBatteryDirective(2006/66/EC),then

the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will appear

below the crossed out wheeled dust bin symbol.

By participating in separate collection of batteries, you will help to assure the proper

disposal of products and batteries and thus help to prevent potential negative

consequences for the environment and human health.

For more detailed information about the collection and recycling programmes available

inyourcountry,pleasecontactyourlocalcityofceortheshopwhereyoupurchased

the product.

In conformity with the WEEE Regulations.

HDR5010 User Guide.indb 5 22/07/2010 10:38

Introduction

End User Licence

This product includes software code developed by third parties, including software code

subject to the GNU General Public License (‘GPL’) or GNU Lesser General Public License

(‘LGPL’). As applicable, the terms of the GPL and LGPL, and information on obtaining

access to the GPL Code and LGPL used in this product, are available to you - please

contact the manufacturer.

The GPL Code and LGPL Code used in this product is distributed WITHOUT ANY

WARRANTY and is subject to the copyrights of one or more authors. For details, see the

GPL Code and LGPL Code for this product and the terms of the GPL and LGPL.

Trademark Acknowledgements

•Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol

are registered trademarks of Dolby Laboratories.

•DVB is a registered trademark of the DVB Project. This logo indicates that the product is

compliant with European Digital Broadcasting.

•HDMI,theHDMIlogoandHigh-DenitionMultimediaInterfacearetrademarksor

registered trademarks of HDMI Licensing LLC.

•The FREEVIEW+ HD words and logos are trademarks of DTV Services Ltd and are used

under licence. © DTV Services Ltd.

EU Conformity Statement

“This product is marked with “CE” and complies therefore with the applicable

harmonizedEuropeanstandardslistedundertheLowVoltageDirective2006/95/EC

and the EMC Directive 2004/108/EC.”

Responsible for CE-marking is TOSHIBA INFORMATION SYSTEMS (U.K.) LTD,

Toshiba Court, Weybridge Business Park, Addlestone Road, Weybridge,

Surrey, KT15 2UL, United Kingdom

HDR5010UserGuide.indb6 22/07/2010 10:38

Table of Contents

Introduction

Important Safety Information ................................................................................................2

General Information ..............................................................................................................4

Notes on Copyright ...............................................................................................................4

Environmental Information....................................................................................................5

End User Licence .................................................................................................................6

Trademark Acknowledgements ............................................................................................6

Getting Started

Package Contents ................................................................................................................8

Overview of the Digital TV Recorder ....................................................................................9

Overview of the Remote Control ........................................................................................10

Inserting the Batteries into the Remote Control..................................................................12

Connecting your Digital TV Recorder .................................................................................13

Switching your Digital TV Recorder On ..............................................................................14

Automatic Tuning ................................................................................................................15

Using your Digital TV Recorder

Everyday Use .....................................................................................................................16

Common Symbols ..............................................................................................................17

The Electronic Programme Guide (EPG) ...........................................................................18

The Channel List ................................................................................................................19

The Info Display..................................................................................................................20

Picture In Picture (PIP) .......................................................................................................21

Recording Programmes......................................................................................................22

Timeshifting ........................................................................................................................25

The Timers Screen .............................................................................................................26

Modifying Timers ................................................................................................................27

The Library Screen .............................................................................................................29

The Photo Viewer ...............................................................................................................31

The Main Menu...................................................................................................................33

Main Menu Structure ..........................................................................................................33

Main Menu Options ............................................................................................................34

Additional Information

Programming the Remote Control ......................................................................................40

Manual Programming the Remote Control .........................................................................41

Finding the Remote Control’s Current Codes.....................................................................41

Troubleshooting ..................................................................................................................42

Specications .....................................................................................................................44

Remote Control Brand Codes ............................................................................................46

Introduction

HDR5010 User Guide.indb 7 22/07/2010 10:38

Package Contents

HDR5010KB

QUICK START MANUAL

Digital TV recorder

Remote control

Batteries (2x R3/AAA)

AC mains adapter*

Owner’s manual

Quick start guide

Helpleaet

* For use exclusively with this Digital TV recorder. Never use this AC mains adapter with any other

device,asitmaycausereand/orproductdamage.

Getting Started

HDR5010 User Guide.indb 8 22/07/2010 10:38

Overview of the Digital TV Recorder

Front Panel

Rear Panel

Aerial input socket

Aerial (loop through)

output socket

LAN socket

HDMI output socket

HDMI input sockets 1/2

USB socket

SPDIF optical output

(Standard TOS link

connector)

Power socket

SCART output socket

Standby / ON switch

and indication

Front panel display

USB socket

w e r t y

i o

Getting Started

HDR5010UserGuide.indb9 22/07/2010 10:38

Overview of the Remote Control

Getting Started

HDR5010 User Guide.indb 10 22/07/2010 10:38

TV - Switches the TV on/into Standby*.

DTT - Switches the viewing mode to DTT.

HDMI 1 - Switches the input mode to HDMI 1.

0-9 - Selects channels, enter PIN.

AD-SwitchesAudioDescriptiononoroff.Refertopage16formoreinformation.

SUB - Displays subtitles (if available).

+/− - Adjusts the TV’s volume*.

PIP - Enters Picture In Picture mode. Refer to page 21 for more information.

CLOCK - Displays the clock.

GUIDE - Switches the Electronic Programme Guide (EPG) on/off. Refer to page 18 for more

information.

BACK-Returnstothepreviouslevelinthemenu.ExitsEPG,Infoandmenu(rstlevel).

LIB-DisplaystheLibraryofrecordedprogrammes.Refertopage29formoreinformation.

MENU - Displays/exits the menu.

- Pauses and resumes live TV. Refer to page 25 for more information about Timeshifting.

Plays and pauses recordings in the Library.

- Stops playback when viewing recordings. Stops recording.

Skips back 30 seconds when viewing a recording or watching live TV. Press and hold to skip

to the start when viewing a recording or skip to the start of the pause buffer when watching live TV.

- Rewinds live TV and recordings. Press repeatedly to increase the rewind speed.

Coloured buttons - Selects options in digital text/EPG/Channel List/menu.

- Fast forwards recordings. Press repeatedly to increase the fast forward speed. When

pausing live TV or recordings, press to watch in slow motion.

- Skips forward 30 seconds when viewing a recording. Press and hold to skip to the end

when viewing a recording.

- Records live TV. Sets highlighted programmes to timer record in the EPG.

TV INPUT -

Switches between the available TV input modes (eg DTT, HDMI or AV).*

TIMER-DisplaystheTimersscreen.Refertopage26formoreinformation.

TEXT - Displays digital text (if available).

OK/ / / / -DisplaystheChannelList/conrmsaselection(OK button). Navigate the EPG/

menu/Channel List/Info menu ( / / / buttons).

INFO - Displays programme and recording information. Refer to page 20 for more information.

SAVER - Displays the screen saver.

TV/RAD - Switches between Digital TV channels and Digital Radio channels.

- Turns the TV’s sound on/off*.

Ch.+/− - Selects the next/previous channel.

- Returns to the previous channel watched. Switches between 4 and 24 hours advance in EPG.

HDMI 2 - Switches the input mode to HDMI 2.

USB - Switches the input mode to USB.

STB - Switches the Digital TV recorder on/into Standby.

*TheremotecontrolmustrstbeprogrammedtooperateyourTV.Refertopage40.

Getting Started

HDR5010 User Guide.indb 11 22/07/2010 10:38

Inserting the Batteries into the Remote Control

1. Lift open the battery compartment cover (as shown).

2. Install 2 “R3/AAA” batteries (included); the correct polarity is shown inside the battery

compartment.

Always check the positive/negative symbols on the batteries to ensure

they are inserted correctly.

3. Replace the battery compartment cover and push down until it clicks shut.

Note:

• Always dispose of old batteries safely. Check with your local council for how you should get rid of batteries.

Neverputbatteriesonareorinthebinwithnormalhouseholdwaste.

• A label with support information is located on the back of the remote control.

Getting Started

HDR5010 User Guide.indb 12 22/07/2010 10:38

Connecting your Digital TV Recorder

Plug your aerial lead into the RF IN socket of the recorder.

If required, plug an Ethernet cable between the LAN socket and an Ethernet

system. Refer to page 37 for more details. Cable not supplied.

If required, plug a SCART cable between the SCART OUTPUT socket of the

recorder and your TV, Video or DVD recorder. Cable not supplied.

If required, plug a RF cable between the RF OUT socket of the recorder and your

TV, Video or DVD recorder. Cable not supplied.

Plug a HDMI cable between the HDMI OUT socket of the recorder and your TV.

Cable not supplied.

If required, plug a HDMI cable between your DVD player, DVD recorder, Set-top box,

Games console and the HDMI IN 1 or 2 socket of the recorder. Cable not supplied.

If required, plug a USB Flash drive or a cable from a Digital Still Camera or Card

reader in to the USB socket. Refer to page 31 for more details.

If required, plug an Optical cable (TOS link) between the SPDIF output socket of

the recorder and your Hi-Fi or Surround Sound System. Cable not supplied.

Plug the supplied AC mains adapter between the power socket of the recorder and

a standard wall socket. Only switch on the wall socket when all cables have

been attached. (Do not cut off the supplied AC mains adapter’s plug.)

Note:

• Refertopage16formoreinformationonhowtochangetheinputmodetoHDMI1or2andUSB.

• AHDMIcableisrecommendedasitgiveshigherqualitypictureandsoundandisrequiredforHighDenition

viewing.

• Socket names vary according to make and model of your equipment.

• The USB socket does not support all USB devices or cameras.

TV aerial

Getting Started

HDR5010 User Guide.indb 13 22/07/2010 10:38

Switching your Digital TV Recorder On

To Turn On Power to the Unit:

1. Switch On power at the wall socket, if required.

2. Within a few seconds the front panel will display “Starting” and the Power ring LED will

light.

3. After start up is complete, an image is displayed on your TV screen and the Power ring

LED will change to Blue.

To Turn Off Power to the Unit:

Press the [ ] button on the remote control or the Standby button on the front of the unit

The Power Ring changes to Red.

2. Press the switch on the wall socket and remove the AC mains adapter, to completely

turn Off the power to the unit.

Standby

When the Red Power LED is on the unit is in Standby. You can go In/Out of Standby by

pressing the [

] button on the remote control or

the Standby button on the front of the unit

Note:

• It is recommended that the unit be left in Standby rather than switching Off completely, in order to allow

important updates to be received via your aerial.

• It is safe to put the Digital TV recorder into Standby mode when you have set programmes to record. The Digital

TV recorder will automatically wake up from Standby mode to make the recording.

• Whenever the unit receives a signal from the remote control, the Power LED blinks Red.

• After turning On, it takes some time before the unit starts up. Please note that buttons on the remote control

and the unit do not work during this period of time.

• Do not switch the power On/Off repeatedly within a short period of time. It could cause a malfunction.

• If a power cut occurs when using the unit, unplug the AC mains adapter to avoid sudden surges of electricity

when the power comes back on.

Front Panel Display

This will give you information about the DTT/Radio channel that is currently being watched

or listened to. It also displays symbols such when using the Digital TV

recorder functions. When using the Photo Viewer function “Photo” is displayed.

Getting Started

HDR5010 User Guide.indb 14 22/07/2010 10:38

Automatic Tuning

1. Ensure the aerial is plugged into this unit.

2. Oncetheunithaspoweredupforthersttime,thefollowingmenuisdisplayed.Press

the [OK] button to continue.

Note:

• On initial startup there is also an option available to access advanced setup by pressing the [RED] button

before tuning starts. Press the [BACK] button to return to the tuning screen.

3. The Digital TV recorder will now scan and store all available channels. Depending on the

quality of your reception, this may take several minutes. Please be patient and do not

press any buttons.

Note:

• Ifnochannelsarefound,amessageisdisplayedaskingyoutocheckyouraerial.Conrmthatyouraerialis

connected correctly and press the [OK] button to restart automatically tuning.

4. Onceautomatictuninghasnished,youmayseearegionpreferencescreensimilarto

the one shown below.

Select the region that is best for your area by pressing the [RED]

button, or to get further regions press the [OK] button (if available).

5. A summary screen, like the one below, is shown. Press the [OK] button to exit the

automatic tuning process.

Congratulations the Digital TV recorder is now ready to use.

Getting Started

HDR5010 User Guide.indb 15 22/07/2010 10:38

Everyday Use

Changing channels

Type in the channel number using the [0]-[9] buttons. Alternatively, press the [Ch+] and

[Ch-] buttons to select the next/previous channel.

Channel hopping

Press the [

] button to return to the previous channel watched. Hop between the current

and previous channel watched

Adjusting the volume*

Press the [

+] and [ -] buttons to increase/decrease the volume.

Muting the sound*

Press the [

] button to mute the sound. Press again to restore.

Displaying Digital Text

Press the [TEXT] button to display digital text (if available). Press again to exit digital text.

Displaying subtitles

Press the [SUB] button to display subtitles (if available). Press again to switch off the

subtitles.

Audio Description

Audio Description is a spoken explanation that describes all important information on a

programme, such as body language, facial expressions, scenery, action, costumes or

anything that helps to describe the plot of the story, event or image.

Press the [AD] button to switch on the Audio Description (If available from the broadcaster).

Press again to switch off the Audio Description.

Switching between TV and Radio channels

The Digital TV recorder stores all the Digital TV channels together and all the Digital Radio

channels together. Press the [TV/RAD] button to switch between Digital TV and Digital

Radio channels.

When you are listening to a radio channel, the screen saver will automatically start if you do

not press any button for a few minutes. Alternatively, press the [SAVER] button to display the

screen saver right away. To remove the screen saver, press any button on the remote control.

Switching between DTT, HDMI 1-2 or USB

While watching Digital TV programmes you can use the [DTT], [HDMI 1], [HDMI 2] or

[USB] buttons to select the input mode.

Note:

• When listening to TV programmes with Audio Description enabled, Dolby Digital sound is not available.

• HDMI pass through is only available when the unit is powered out of Standby and using HDMI output from this

unit.

*TheremotecontrolmustrstbeprogrammedtooperateyourTV.Refertopage40.

Using your Digital TV recorder

HDR5010UserGuide.indb16 22/07/2010 10:38

Everyday Use

Using Standby

When you’re not watching TV, you should set the Digital TV recorder to Standby. Press the

[ ] button to switch between On (Blue Power ring LED on the front panel) and Standby

(Red power LED on the front panel). This unit has a low power feature which means that

when left in Standby for a long period, it may take longer to power up.

It is safe to put the Digital TV recorder into Standby when you have set programmes to

record. The Digital TV recorder will automatically wake up from Standby to make the

recording. If you plan to leave the Digital TV recorder unattended for a long period and have

not set any programmes to record, put the Digital TV recorder into Standby and wait for 20

seconds before switching it off at the mains socket. If the mains socket doesn’t have a switch

unplug the AC mains adapter.

Automatic Standby

To help reduce the amount of electricity it uses, the Digital TV recorder will automatically

switch into Standby after 3 hours of inactivity. If you are still watching TV at this time, a

screen will be displayed allowing you to stop the Digital TV recorder entering Standby.

If no button is pressed while this screen is displayed, the Digital TV recorder will enter

Standby after a few seconds. It is possible to deactivate automatic Standby by setting the

Auto Standby option in the General Settings menu to Off. Refer to page 35.

Common Symbols

The following may be visible in the Electronic Programme Guide, Channel List, Info

display, Timers screen and Library menus.

Locked channel. Multiple audio languages available.

Encrypted/scrambled channel. Teletext available.

Radio Channel. Timer has been set.

Channel selected for moving.

[

]

Subtitles available.

Recording has been viewed. Selected channel is hidden.

Timer is set to “Series Record”. Playback of recording has been locked.

Recording has been protected from

deletion.

Play.

Pause. Record.

Slow motion. Fast Forward.

Rewind. FastForward(x16).

FastRewind(x16). Fast Forward (x128).

Fast Rewind (x128).

HighDenition.

[

]

Audio Description available.

Using your Digital TV recorder

HDR5010 User Guide.indb 17 22/07/2010 10:38

The Electronic Programme Guide (EPG)

The EPG displays programme information for the next 8 days (when transmitted by

broadcasters). You can also set programmes to be recorded from the EPG.

To Press

Access the EPG... [GUIDE] button.

Move around the EPG... [

/ / / ] buttons or [0]-[9] buttons to

directly enter the channel number.

Display the previous nine channels in the

list...

[RED] button.

Display the next nine channels in the list... [GREEN] button.

Move forward 4 or 24 hours... [BLUE] button.

(Press to switch between 4 and 24 hours)

Move back 4 or 24 hours... [YELLOW] button.

(Press to switch between 4 and 24 hours)

View information for the highlighted

programme...

[INFO] button. Press again to return to the

EPG.

Set a highlighted programme to record...

[

] button. Refer to page 23 for Recording

options.

Preview a current programme

(in the background)...

[OK] button.

Exit the EPG and switch to a previewed

programme...

[OK] button.

Exit the EPG... [GUIDE] or [BACK] button.

Note:

• If you accidentally set a wrong programme to record, press the [

] button again to cancel.

Current

channel

Date of

currently

displayed

programmes

List of

channels

Today’s

date and

current time

Time of

currently

displayed

programmes

Programme

information

Using your Digital TV recorder

HDR5010 User Guide.indb 18 22/07/2010 10:38

The Channel List

The Channel List displays all the available channels.

To Press

Access the Channel List... [OK] button while watching TV.

Select channels... [

/ ] buttons.

Display the previous nine channels in the

list...

[RED] button.

Display the next nine channels in the list... [GREEN] button.

Switch to the selected channel... [OK] button.

Exit the Channel List... [BACK] button.

List of

channels

Highlighted

channel

Using your Digital TV recorder

HDR5010UserGuide.indb19 22/07/2010 10:38

The Info Display

When watching TV, the Info display gives brief information on the current and future

programmes (when the programme information is transmitted by broadcasters). You can

also set programmes to be recorded from the Info display. When watching a recording, the

Info display gives a brief description of the recorded programme.

To Press

Access Info for the current programme/

recording...

[INFO] button.

View information for future programmes on

the current channel...

[RIGHT] button.

View information for programmes on other

channels...

[

/ ] buttons.

Change the Audio setting (if available)... [RED] button.

Change the Subtitle setting (if available)... [GREEN] button.

Change Audio Description language

(if available)...

[YELLOW] button.

Switch to another channel (when viewing

that channel’s information)...

[OK] button.

Set a current or future programme to

record...

[ ] button (whilst viewing that programme’s

information). Refer to page 22 for more

information.

Exit Info... [INFO] or [BACK] button.

Selected

programme’s

details

Today’s

date and

current

time

Selected programme’s

start and end time

Programme

name

Channel

Using your Digital TV recorder

HDR5010 User Guide.indb 20 22/07/2010 10:38

Picture In Picture (PIP)

Picture In Picture allows you to watch two channels at the same time. The sound from the

main picture is always played.

To Press

Switch on Picture In Picture... [PIP] button.

Move the PIP screen... [

/ / / ]

buttons.

Select/highlight the PIP screen... [PIP] button.

Change the channel displayed in the PIP

screen...

[Ch+/-] buttons, when the PIP screen is

selected.

Change the channel displayed in the main

picture...

[0]-[9] buttons. The [Ch+/-] buttons can

also be used when the PIP screen is not

selected.

Swap the channels on the PIP screen and

the main picture...

[

] button.

Exit Picture In Picture... [PIP] button, when the PIP screen is

selected/highlighted.

Note:

• Picture In Picture is not available when recording programmes.

PIP screen

(highlighted)

Using your Digital TV recorder

HDR5010 User Guide.indb 21 22/07/2010 10:38

Recording Programmes

This Digital TV recorder has twin tuners, making it possible to record two programmes at

the same time.

When recording two programmes at the same time you can also:

- watch either of the programmes you are recording.

- start to playback one of the recordings, even though it’s still recording !

- playback a previously recorded programme

- watch either of the programmes being recorded.

When recording two programmes at the same time you can not:

- timeshift/pause live TV.

- use Picture In Picture.

- watch a third TV channel.

Recording TV Programmes

There are 4 different ways to record programmes:

1. Instant recording

•While watching a programme, press [ ] to start recording.

•Press [

] to stop recording.

2. Recording from the Electronic Programme Guide (EPG)

•With the required programme highlighted in the EPG, press the [ ] button to set the

recording.

Note:

• For full details on the EPG, refer to page 18.

3. Recording from the Info display

•With the required programme highlighted in the Info display, press the [ ] button to set

the recording.

Note:

• For full details on the Info display, refer to page 20.

4. Manually recording

•With the Timers screen displayed, press the [YELLOW] button to manually set a

recording.

Note:

• ForfulldetailsontheTimersmenu,refertopage26.

Using your Digital TV recorder

HDR5010 User Guide.indb 22 22/07/2010 10:38

Recording Programmes

Recording Options

Below is the bottom part of an on screen menu that may appear when you make a

recording. The number of options available may vary.

If you do not wish to use any of these options press the [OK] button or simply wait until

the menu disappears.

There are 3 options that you may see in this menu:

1. HD alternative

WhensettingaStandardDenition(SD)programmetorecord,theHDAlternativeoption

will appear if there is a HD version of this programme available. Press the [RED] button

and HD alternative will be recorded instead.

2. Try this (Recommendations)

This allows you to record a selected list of related programmes. If, for example, you set a

recording for Panorama, the recommendations would contain similar programmes such as

Horizon. Press the [YELLOW] button if you would like these programmes to be recorded.

To ensure that the Series and Try this are also for HD, choose the HD option before

selecting Series or Try this options.

Note

• The broadcaster controls the content of the recommendations and these may be the same as the recordings for

the Series.

3. Series record

This allows you to record an entire series at the push of a button (when supported by the

broadcaster). If the programme you are setting is part of a series, press the [BLUE] button

torecordtheentireseries.Programmessettorecordaspartofaseriesareidentiedin

the “Timers” menu with a

symbol.

Trailer booking

When there is a trailer for a TV programme (e.g. just before or after Eastenders) a symbol

may be displayed on screen (when supported by broadcasters).

To use this feature press the

[GREEN] button and select the programme(s) you wish to record.

Note

• GototheTimersscreentochecktherecordedprogram,andthetimercanbemodied(Refertopage26/27for

more information).

Using your Digital TV recorder

HDR5010 User Guide.indb 23 22/07/2010 10:38

Recording Programmes

RecordingConicts

Your Digital TV recorder can record up to two programmes at the same time.

If you attempt to record three or more programmes that overlap, the unit will try to resolve the

conictautomaticallybyrecordingtheprogrammeatadifferenttimeoronadifferentchannel.

If it can not, you will be asked to either select an alternative time to record the programme

(Resolveconict)orcanceltherecordingrequestyouhavejustmade(Canceltimer).

You will then be presented with a list of all the programmes that overlap.

If one of the programmes is repeated later in the week then, when it is highlighted, the box

will give you the option to press the [GREEN] button (Alternative) to record the repeated

programme instead. If none of the programmes are repeated, simply delete one of the

planned recordings by pressing the [RED] button (Delete).

Note:

• The Digital TV recorder will record programmes even if the programme is shown later than advertised e.g. due

to a previous programme overrunning. Please note, this is not applicable for timers set manually.

• It is safe to put the Digital TV recorder into Standby when you have set programmes to record. The Digital TV

recorder will automatically wake up from Standby to make the recording.

• The Digital TV recorder will also automatically add 3 minutes to the end of each recording to make sure the

entire programme is recorded. However, if any subsequent recording starts during those 3 minutes, then the

rstrecordingwillbestoppedtoallowthenewrecordingtocommence.

Using your Digital TV recorder

HDR5010 User Guide.indb 24 22/07/2010 10:38

Timeshifting

Timeshifting allows you to Pause live TV, it lets you pause a broadcast programme and

continue watching it later. The maximum length of time you can pause a programme for is

4 hours.

Pausing Live TV

•Press to pause live TV. Press to resume.

Note:

• When live TV is paused, the timeshifting banner is displayed indicating how long the programme has been paused.

• The length of time you can pause a programme can be adjusted in the menu. See ‘Pause Buffer Size’ on page 35.

Rewinding Live and Timeshifted TV

•Press to rewind live TV. Press to resume.

Note:

• You can press

a further 3 times to rewind faster.

Fast Forwarding Timeshifted TV

•Press to fast forward timeshifted TV. Press to resume.

Note:

• You can press

a further 3 times to fast forward faster.

Watching in Slow Motion

•Press to pause live TV or a recording.

•Press to watch in slow motion. Press to return to normal.

Stopping Timeshifting

•Press .

Timeshift

banner

Using your Digital TV recorder

HDR5010 User Guide.indb 25 22/07/2010 10:38

The Timers Screen

The Timers screen displays all the programmes that are currently set to record. You can

also set a manual timer and modify or cancel an existing timer from the Timers screen.

To Press

Access the Timers menu... [TIMER] button.

Select a timer event... [

/ ] buttons.

View additional pages of timer events

(if available)...

[

/ ] buttons.

Delete the selected timer event... [RED] button. If the timer selected is for a

series you will be asked whether to delete

all timers in the series or just this instance.

Modify the selected timer event... [GREEN] button (see following page for

more details).

Manually set a timer... [YELLOW] button (see following page for

more details).

Show all timers currently set (including all

‘Series Record’ programmes)...

[BLUE] button. Press again to display a

summary of all timers currently set.

Exit the Timers menu... [TIMER] or [BACK] button.

Note:

• The number of hours displayed as Free and for the Library and Timers are approximate only. These are based

onrecordingStandardDenitionTVprogrammes.IfrecordingHighDenitionTVprogrammesthenthenumber

of hours will change.

List of

timers

Today’s

date and

current time

Size of

current

recordings

Size of

current

timers

symbol

indicates

that Series

Record

is set

Available

recording

space

symbol

indicates

that the timer

is protected

from deletion

Using your Digital TV recorder

HDR5010UserGuide.indb26 22/07/2010 10:38

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba HDR5010 in the language / languages: English as an attachment in your email.

The manual is 4,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toshiba HDR5010 Manual

Product: