481935
138
Zoom out
Zoom in
Previous page
1/183
Next page
Error Messages
-138-
Power OFF/ON
%ERRCODE%: Error %FATALSTRING1%
Blinks An error has occurred in the device.
Turn the machine off and then on again.
If the same error occurs, turn the machine off
and then on again. If the error is not resolved, or
the same error occurs again, contact your dealer.
Document Jam
Please open the scanner unit and the ADF
cover.
Please see Help for details.
Blinks A document jam has occurred.
Open the ADF cover, and then remove the
jammed paper.
Lamp Error. Please call service.
<%CODE%>
Please see Help for details.
Blinks Indicates that a lamp error has occurred.
This message is displayed because of the light
intensity of the lamp is weak.
Contact your dealer.
%TRAY% missing.
Please see Help for details.
Lights up A paper cassette is not in the indicated tray.
Insert the paper cassette into the indicated tray.
If the cassette is already inserted in the machine,
pull out the cassette and set it again to correctly
locate it.
430
440
Please close %TRAY%.: 430,440
To cancel, select [Cancel]
Blinks A paper cassette is not in the indicated tray.
Insert the paper cassette into the indicated tray.
If the cassette is already inserted in the machine,
pull out the cassette and set it again to correctly
locate it.
Inspection is required.
%ERRCODE%: SIP Error
Blinks Processing of scanned image has failed.
Turn the machine off and then on again.
If the error is not resolved, contact your dealer.
Please call service.
Scanner unit failed to detect printer unit.
Blinks An error has occurred between the scanner and
printer units.
Turn the machine off and then on again.
If the error is not resolved, contact your dealer.
SIP Firmware Missing Blinks A board failure has been detected.
Turn the machine off and then on again.
If the error is not resolved, contact your dealer.
Wait a moment.
Network initializing ...
Lights up Changed network settings are being stored.
085 Please change SD Memory Card.
Error Code: 085
Lights up The contents of the SD memory card cannot be
read normally.
If the same card is used further, the same error
may occur. Replace the SD memory card.
Power OFF/ON
Carriage Error <1>
Please see Help for details.
Blinks Indicates that a carriage error has ocurred.
This message is displayed because of the
scanner carriage is not working normally.
If the error is not resolved, contact your dealer.
Power OFF/ON
Carriage Error <%CODE%>
Blinks Indicates that the following carriage error has
occurred.
2 : Home position error (carriage connection
error)
3 : Scanning start position detection error
If the error is not resolved, contact your dealer.
581 Please close faceup stacker.
581:Cannot print with duplex.
Blinks Although Duplex printing was attempted, the
FaceUp stacker is open and Duplex printing is
disabled.
500 Please install paper on
Manual Feeder. Please set paper
(%MEDIA_SIZE%).
To cancel, select [Cancel]
Blinks Manual paper feed is required. Manually insert
the paper shown by %MEDIA_SIZE%.
Error
code Message
<Status>
key
Cause/Remedy
138


Need help? Post your question in this forum.

Forumrules
1

Forum

toshiba-e-studio-403s

Reset search

  • hello, i bought toshipa estudio 403s used in good condition but i can not access the webpage as admin, also i can not scan from network, i installed every drivers and applications i found on internet but with no luck. please Help Submitted on 4-3-2021 at 16:16

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba e-STUDIO 403S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba e-STUDIO 403S in the language / languages: English as an attachment in your email.

The manual is 22.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toshiba e-STUDIO 403S

Toshiba e-STUDIO 403S User Manual - German - 206 pages

Toshiba e-STUDIO 403S User Manual - German - 202 pages

Toshiba e-STUDIO 403S User Manual - German - 137 pages

Toshiba e-STUDIO 403S User Manual - Dutch - 198 pages

Toshiba e-STUDIO 403S Quick start guide - Dutch - 131 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info