481869
18
Zoom out
Zoom in
Previous page
1/82
Next page
Chapter 1 PREPARATIONS
16
Saving energy when not in use – energy saving modes –
This equipment supports three energy saving modes; the Automatic Energy Save mode, Sleep mode and Super Sleep
mode. The table below shows the procedures to switch modes manually and the conditions under which the equipment
enters into or recovers from each mode.
Energy saving
modes
Procedure to switch
modes
Conditions to enter into
the mode Status of equipment Conditions to recover
from the mode
Automatic
Energy Save
mode
When a specied period of
time *1 has passed since the
last use of the equipment.
“Saving energy - press
START button. appears on
the touch panel.
When a button on the
control panel *2 is pressed
or when print data or fax
data are received.
Sleep mode
When the [ENERGY SAVER]
button *3 is pressed or
when a specied period of
time *4 has passed since the
last use of the equipment.
When a particular option *5
is installed or when a
particular protocol *6 is
enabled.
The touch panel display
goes o and the [ENERGY
SAVER] button lights in
green.
Same as the Automatic
Energy Save mode.
Super Sleep
mode
When the [ENERGY SAVER]
button *3 or the [POWER]
button *7 is pressed or
when a specied period of
time *4 has passed since the
last use of the equipment.
When a particular option *5
is not installed and also
when a particular protocol
*6 is disabled.
Only the MAIN POWER
lamp (red) lights.
When the [POWER] button
is pressed, when print or
fax data are received
through a wired LAN or
when the time set for
Scheduled Print has come.
*1 The default value set at the factory shipment is 1 minute.
*2 Any of the [START], [ENERGY SAVER], [COPY], [e-FILING], [SCAN], [PRINT] and [FAX] buttons.
*3 [ENERGY SAVER] button on the control panel.
*4 The default value set at the factory shipment is 1 minute (The default value set at the factory shipment of the European version is 10 minutes).
*5 Any of the Wireless LAN Module, Bluetooth Module and e-BRIDGE ID Gate.
*6 Any of IPX, AppleTalk and other protocols. When the IPsec function is enabled, the equipment enters into the Sleep mode. For details, refer to the
following guide:
& TopAccess Guide (PDF): “Chapter 8: [Administration] Tab Page” - “[Setup] Item list”
*7 Even if you press the [Power] button, the equipment may not enter into the Super Sleep mode and the power may be turned OFF, depending on the
state of the equipment. For the conditions under which the equipment enters into the Super Sleep mode, refer to the following guide:
& TopAccess Guide (PDF): “Chapter 8: [Administration] Tab Page” - “[Setup] Item list”
For changing the set period of time for entering into each mode, refer to the following guide:
& MFP Management Guide (PDF): “Chapter 2: SETTING ITEMS (ADMIN)” - “Setting General Functions”
When the set period of time for switching to the Automatic Energy Save mode is the same as that for the Sleep mode or
the Super Sleep mode, the equipment enters into the Sleep mode or the Super Sleep mode after the set period of time.
For the European version
Contact your service representative to change the default settings noted above.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba e-studio 2040C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba e-studio 2040C in the language / languages: English as an attachment in your email.

The manual is 7.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toshiba e-studio 2040C

Toshiba e-studio 2040C User Manual - German - 84 pages

Toshiba e-studio 2040C User Manual - Dutch - 198 pages

Toshiba e-studio 2040C Quick start guide - Dutch - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info