681689
61
Zoom out
Zoom in
Previous page
1/99
Next page
Troubleshooting
9.5
Low Heat Error There is a problem in
the fuser unit.
Unplug the power cord and
plug it back in. If the problem
persists, please call for
service.
Open Heat Error
[Over Heat]
Group Not
Available
You have tried to
select a group location
number where only a
single location
number can be used,
such as when adding
locations for a
broadcast operation.
Use a speed dial number or
dial a number manually using
the number keypad.
[Incompatible] The remote machine
did not have the
requested feature,
such as a delayed
transmission.
This message also
occurs if the remote
machine does not
have enough memory
space to complete the
operation you are
attempting.
Reconfirm the remote
machine’s features.
[Line Busy] The receiving party
did not answer or the
line is already
engaged.
Try again after a few minutes.
[Line Error] Your machine cannot
connect with the
remote machine or
has lost contact
because of a problem
with the phone line.
Try again. If the problem
persists, wait an hour or so
for the line to clear and try
again.
Or, turn the ECM mode on.
See “ECM Mode (Error
Correction Mode)” on
page 7.14.
Load Document You have attempted
to set up a copy or fax
operation with no
document loaded into
the ADF.
Load a document into the ADF
and try again.
[LSU Error] A problem has
occurred in the LSU
(Laser Scanning Unit).
Unplug the power cord and
plug it back in. If the problem
persists, please call for
service.
Memory Dial Full The fax jobs queue in
the memory is full.
Cancel unnecessary fax jobs
in the memory.
Display Meaning Suggested solutions
Memory Full The memory is full. Delete unnecessary
documents and retransmit
after more memory becomes
available. Alternatively, split
the transmission into more
than one operation.
[No Answer] The receiving fax
machine has not
answered after
several redial
attempts.
Try again. Make sure that the
receiving machine is
operational.
[No Cartridge] The toner cartridge is
not installed.
Install the toner cartridge.
See “Installing the Toner
Cartridge” on page 2.2.
Not
Assigned
The speed dial
location you tried to
use has no number
assigned to it.
The ID you entered
is not assigned
.
Dial the number manually
using the number keypad or
assign the number. For
storing a number, see
Automatic Dialing” on
page 7.8.
Enter the correct ID.
.
[No Paper]
Add Paper
The paper in the tray
has run out.
Load paper in the tray. See
“Loading Paper” on page 2.3.
Operation
Not Assigned
You are doing the
Add/Cancel operation,
but there are no jobs
waiting.
Check the display to see if
there are any scheduled jobs.
The display should indicate
them in Standby mode; for
example, Delay Fax.
Out of Range The current date and
time you entered is
not correct
.
Enter the correct date and
time
.
[Paper Jam 0]
Open/Close Door
Paper has jammed in
the feeding area of
the tray.
Clear the jam. See “In the
Tray” on page 9.2.
[Paper Jam 1]
Open/Close Door
Paper has jammed in
the fuser area or
around the toner
cartridge.
Clear the jam. See “In the
Fuser Area or Around the
Toner Cartridge” on page 9.3.
[Paper Jam 2]
Check Inside
Paper has jammed in
the paper exit area.
Clear the jam. See “In the
Paper Exit Area” on page 9.3.
[Power Failure] Power has turned off
then on and the
machine’s memory
has not been saved.
The job which you were trying
to do before the power failure
must be completely re-done.
Display Meaning Suggested solutions
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba e-STUDIO 200s at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba e-STUDIO 200s in the language / languages: English as an attachment in your email.

The manual is 3,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toshiba e-STUDIO 200s

Toshiba e-STUDIO 200s User Manual - German - 99 pages

Toshiba e-STUDIO 200s Quick start guide - Dutch - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info