681697
19
Zoom out
Zoom in
Previous page
1/84
Next page
1
19
Turning ON/OFF
Saving energy when not in use – energy saving modes –
The following modes are available; Automatic Energy Save mode, Sleep mode, and Super Sleep mode.
The table below shows the procedures to switch modes manually and conditions under which it enters
into or recovers from each mode.
Energy saving
modes
Procedure to switch
modes
Conditions to enter
the mode Status of equipment Conditions to recover
from the mode
Automatic
Energy Save
mode
When a specified
period of time *1 has
passed since the last
use of the equipment.
A message is displayed
to indicate the energy
saving status.
When you press the
[ENERGY SAVER]
button, or when print
data or fax data are
received.
Sleep mode
When you press the
[ENERGY SAVER]
button*2 or when a
specified period of
time *3 has passed.
When a particular
option *4 is installed or
when a particular
protocol *5 is enabled.
The touch panel
display turns o and
the [ENERGY SAVER]
button turns green.
Same as the Automatic
Energy Save mode.
Super Sleep
mode
When you press the
[ENERGY SAVER]
button*2 or when a
specified period of
time *3 *6 has passed.
When a particular
option *4 is not
installed and also a
particular protocol *5 is
disabled.
The touch panel
display turns o and
the [ENERGY SAVER]
button turns green.
When you press the
[ENERGY SAVER]
button, when print or
fax data are received
through a wired LAN,
or when the time set
for Scheduled Print
has come.
*1 The default value is 1 minute.
*2 The [ENERGY SAVER] button on the control panel.
*3 The default value is 1 minute .
*4 The Wireless LAN/Bluetooth Module.
*5 Any of IPX, AppleTalk and other protocols. When the IPsec function is enabled or the Ethernet speed is set to [AUTO
(-1000MB)] or [1000BASE FULL], the equipment enters Sleep mode. For details, see the following guide:
& TopAccess Guide (PDF) : “Chapter 8: [Administration] Tab Page” - “[Setup] Item List”
*6 Depending on the network environment, the time for switching to Super Sleep mode may take more than 10 minutes even if
it is set to 10 minutes or less.
To change the time for entering each mode, see the following guide:
& MFP Management Guide (PDF) : “Chapter 2: SETTING ITEMS (ADMIN)” - “GENERAL
For the European version
Contact your service representative to change the default settings.
When the set time for switching to Automatic Energy Save mode is the same as Sleep mode or Super
Sleep mode, the equipment enters into Sleep mode or Super Sleep mode.
If an original is placed on the original glass during energy saving mode, the size is not detected even when the
equipment recovers from this mode. Aer pressing the [START] button or the [POWER] button to recover from
the mode, place it on the glass again.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba e-STUDIO 2000ac at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba e-STUDIO 2000ac in the language / languages: English as an attachment in your email.

The manual is 18.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toshiba e-STUDIO 2000ac

Toshiba e-STUDIO 2000ac User Manual - German - 178 pages

Toshiba e-STUDIO 2000ac User Manual - German - 428 pages

Toshiba e-STUDIO 2000ac User Manual - Dutch - 184 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info