481919
97
Zoom out
Zoom in
Previous page
1/116
Next page
Before Calling Service Technician 95
Before Calling Service Technician
When you encounter trouble while using this equipment, check the items listed below again.
General operation
Phenomenon Usual cause Countermeasure
The equipment does not
operate at all.
The power cable is not
plugged in securely.
Plug in the power cable securely.
The equipment does not
operate even when you press
any of the buttons.
Any of the message lamps is
lit or blinking.
Check which lamp is lit or blinking and
take any countermeasure accordingly.
P.78 “When Message Lamp is Lit/
Blinking”
The equipment is in the
energy saving mode.
Press the [ENERGY SAVER] button to
cancel this mode.
P.29 “Saving energy when not in use -
Energy saving mode -”
The access code needs to
be keyed in (when the equip-
ment is managed under the
access code function).
Key in the 3-digit access code.
(For the details of the access code set-
ting, ask your service technician.)
It has been a short time
since the power was turned
ON.
Wait for the completion of warm-up and
then try again.
Scanning stops in the middle.
(The [FUNCTION CLEAR]
lamp is blinking.)
The number of pages
scanned has exceeded the
maximum value.
Press the [FUNCTION CLEAR] button.
(The data scanned so far will be deleted.)
Scanning stops in the middle.
(The [START] lamp is lit and
the [FUNCTION CLEAR]
lamp is blinking.)
The built-in memory of the
equipment has become full.
Press the [START] button to copy the data
scanned so far. Press the [FUNCTION
CLEAR] button to delete the data
scanned so far.
Copying stops in the middle.
(The [START] lamp and the
middle paper jam position
lamp ( ) are lit and the
[FUNCTION CLEAR] lamp is
blinking.)
250 sheets of paper have
continuously exited.
Remove the paper from the receiving tray,
and then press the [START] button. Copy-
ing resumes. Press the [FUNCTION
CLEAR] button to end the copy job.
“ALP” appears on the LED
display.
The equipment is in the low
power mode.
The equipment automatically enters into
this mode when a specified period of time
has passed since its last use. Copying is
enabled.
“SLP” appears on the LED
display.
The equipment is in the
sleep mode.
The equipment automatically enters into
this mode when a specified period of time
has passed since its last use. Warm-up
starts either when print data are received
or when any button on the control panel is
pressed. Copying is enabled when the
warm-up has finished.
97


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba e-STUDIO 163 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba e-STUDIO 163 in the language / languages: English as an attachment in your email.

The manual is 4.13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toshiba e-STUDIO 163

Toshiba e-STUDIO 163 User Manual - German - 116 pages

Toshiba e-STUDIO 163 User Manual - Dutch - 124 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info