45983
36
Zoom out
Zoom in
Previous page
1/74
Next page
36
XV540U (E/F) Web 213:276
Chapter 5: Setting up your TV
Configuring the input source for the
ANT/CABLE terminal
To configure the ANT/CABLE input source:
1 Press Y and open the Setup menu.
2 Highlight Installation and press T. A new set of
Installation menu icons will appear, as shown below.
3 Open the Terrestrial menu, highlight Input
Configuration, and press T.
4 Press B and C c to select the input source (Cable or
Antenna) for the ANT/CABLE input on the TV.
5 To save your new settings, highlight Done and press T.
To revert to your original settings, highlight Cancel and
press T.
Programming channels into the
TV’s channel memory
When you press < or , on the remote control or TV control
panel, your TV will stop only on the channels you programmed
into the TV’s channel memory.
Follow the steps below to program channels into the TV’s
channel memory.
Programming channels automatically
Your TV can automatically detect all active channels in your
area and store them in its memory. After the channels are
programmed automatically, you can manually add or erase
individual channels in the channel memory.
Note:
If the ANT/CABLE input signal type is set to Cable, the
automatic channel programming process erases channels
that were previously programmed into the TV’s memory.
If the ANT/CABLE input signal type is set to Antenna, the
automatic channel programming process adds newly found
channels to the existing set of programmed channels (and
does NOT erase channels that were previously
programmed into the TV’s memory.) To remove an Antenna
source channel from the memory, you must manually delete
it.
To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the
remote control.
Programming channels when the ANT/CABLE input is
configured for Cable will take substantially longer than when
the ANT/CABLE input is configured for Antenna. This is
normal; however, once channel programming is finished,
you should not have to repeat the programming process
again unless your Cable TV service lineup changes
significantly.
To program channels automatically:
1 You must configure the ANT/CABLE input source, if
you have not already done so (
- page 36).
2 From the Setup menu, highlight Installation and press
T. A new set of Installation menu icons will appear.
Installation
REGZA-LINK Setup
PC Settings
Power-On Mode
Demo Mode Off
Setup
Sleep Timer
HDMI Settings
Power-Saving
Installation
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Channel Tuning Mode Auto
Signal Meter
Input Configuration
ANT/CABLE In Cable
Cancel Done
42XV540U_EN.book Page 36 Thursday, March 6, 2008 11:06 AM
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba 42XV540 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba 42XV540 in the language / languages: English as an attachment in your email.

The manual is 3,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info