807516
84
Zoom out
Zoom in
Previous page
1/92
Next page
84
DE EN
Installation
5
4
3
2
1
1. Position the thrust washer (1) on the motor shaft (2).
2. Position the propeller on the motor shaft, noting the installation direction.
3. Position the washer (3) on the motor shaft.
NOTE! Component damage due to thread locking varnish. Do not use locking
varnishes or additives.
4. Screw the lock nut SW17 (4) onto the motor shaft and tighten it.
Lock nut: 11+/- 1 Nm, 97+/-1 in-lbs
5. Install the galvanic anode (5).
10.4.5 Anti-fouling coating
NOTE! Observe national regulations on the processing, application, use and
disposal of anti-fouling coatings. Follow the manufacturer's instructions and
processing instructions.
General instructions
To keep your Cruise system free of fouling, you can do the following:
Remove the Cruise system from the water after each use and clean it.
Regularly clean all components of the Cruise system that are permanently
below the water surface.
Use an anti-fouling coating.
Cleaning the components under the water surface
Before cleaning work, switch off the Cruise system at the main switch and
secure it against being switched on again by pulling off the switch handle.
Do not use tools with sharp edges or abrasive surfaces that may damage
the Cruise system's paintwork.
Using anti-fouling coatings
When using anti-fouling paints, we recommend treating all parts of the
Cruise system that are permanently below the water surface.
1. Clean the surfaces of the Cruise system that you want to treat.
NOTE! Do not use abrasives to roughen the surface, otherwise the protective
coating will be damaged.
2. Thoroughly mask the anodes and, if necessary, the motor shaft.
3. Observe the processing instructions and the manufacturer's instructions on
personal protective equipment for the respective anti-fouling coating.
Permitted anti-fouling coatings
International Trilux 33 in combination with primer Primocon Sperrgrund
Hempel Silic One in combination with Hempel Light Primer and Hempel
Silic One Tiecoat
NOTE! Do not use metal-containing anti-fouling coatings e.g.products
containing copper.
11 Errors and troubleshooting
11.1 Error messages and errors
Display Cause Troubleshooting
E02 Stator overtemperature
(motor overheated)
After a short waiting time (approx. 10
minutes), the motor can be operated
slowly. Contact Torqeedo Service.
84


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Torqeedo Cruise 6.0 R-T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Torqeedo Cruise 6.0 R-T in the language / languages: English, German as an attachment in your email.

The manual is 3.6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Torqeedo Cruise 6.0 R-T

Torqeedo Cruise 6.0 R-T User Manual - Dutch, Danish - 92 pages

Torqeedo Cruise 6.0 R-T User Manual - French, Italian - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info