807535
71
Zoom out
Zoom in
Previous page
1/92
Next page
71
DE EN
4. Position the connector plugs (1) on the corresponding port of the compo-
nent (2), making sure that the nose of the plug slides into the groove of the
component (3).
5. Screw the connection plug hand-tight.
6. Connect all the data network connectors.
7. Roll up the excess cable and secure it. (e.g. with cable ties).
Power cable
1. Lay the system power cables.
2. Attach the power cables to the designated places according to your plans.
3. Note the minimum bending radius.
4. Make sure that the cables are laid without tension or load.
5. Make sure that the battery main switch is in the "OFF" position and secured
against being switched on again by pulling off the switch handle.
6. Connect the red positive power cable to the positive terminal of the battery,
observing the tightening torque - see connection diagram.
7. Connect the black negative power cable to the negative terminal of the
battery, observing the tightening torque - see connection diagram.
8. Connect the plug connection of the power cables and x them in the desig-
nated place according to your plans.
NOTE! Observe the sequence when disconnecting the power cables, e.g. if you
want to disconnect for storage, see chapter “Storage”.
NOTE! Power cables must not be coiled.
Earth cable
NOTE: If a second earthed on-board power system is available, make sure that
both systems use a common earthing point, see connection diagram.
3
2
1
1. Observe the required cable cross-section of the earth cable.
2. Lay the earth cable according to your diagrams and secure it. Observe the
minimum bending radius of the earth cable used.
3. Position the ground wire (1) on the clamping ring (2) (see Installing the
motor) and install the screw (3). Tighten the screw with 4.5 Nm.
NOTE! For more information on the earth cable, see the corresponding connec-
tion diagram.
Charger unit
DANGER
Danger of injury or death from electric shock. This can result in sever injuries
or death.
Make sure that the charger unit is disconnected from the power source.
1. Lay the charger unit cables according to your diagrams and x them in the
designated places.
2. Connect the red positive cable of the charger unit to the positive terminal of
the battery, observing the tightening torque - see connection diagram.
3. Connect the black negative cable of the charger unit to the negative
terminal of the battery, observing the tightening torque - see connection
diagram.
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Torqeedo Cruise 3.0 FP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Torqeedo Cruise 3.0 FP in the language / languages: English, German as an attachment in your email.

The manual is 2.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Torqeedo Cruise 3.0 FP

Torqeedo Cruise 3.0 FP User Manual - Dutch, Danish - 92 pages

Torqeedo Cruise 3.0 FP User Manual - French, Italian - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info