Manual Topcom Twintalker 4710 Duo Combi Pack (page 63 of 76) (English, German, Dutch, French)

469820

Zoom out

Zoom in

1/76

Twintalker 4710 Duo Combi Pack

PMR

USER GUIDE / HANDLEIDING

MANUEL D’UTILISATEUR / BEDIENUNGSANLEITUNG

v 1.1

0197

UK The features described in this manual are published with reservation to

modifications.

NL De in deze handleiding beschreven mogelijkheden worden gepubliceerd

onder voorbehoud van wijzigingen.

FR Les possibilités décrites dans ce manuel sont publiées sous réserve de

modifications.

D Die in dieser Bedienungsanleitung umschriebenen Möglichkeiten, werden

vorbehaltlich Änderungen publiziert.

Illustration 3 / Afbeelding 3

Illustration 3 / Abbildung 3

Illustration 1 / Afbeelding 1

Illustration 1 / Abbildung 1 Illustration 2 / Afbeelding 2

Illustration 2 / Abbildung 2

Twintalker 4710 DCP

2021222324

1528 29 30

2 UCOM Twintalker 4710 DCP

UCOM Twintalker 4710 DCP

1Introduction 4

2 Intended purpose 4

3 CE Mark 4

4 Safety instructions 4

4.1 General 4

4.2 Burning injuries 4

4.3 Injuries 4

4.4 Danger of explosion 5

4.5 Poisoning danger 5

4.6 Legal 5

4.7 Notes 5

5 Cleaning and maintenance 5

6 Disposal of the device (environment) 6

7 Using a PMR device 6

8 Included in the package 6

9 Getting started 7

9.1 Installing/Removing the Belt Clip 7

9.2 Battery Installation 7

10 Charging batteries 8

11 Battery Charge Level 8

12 Description 9

13 LCD Display information 9

14 Using the Twintalker 4710 10

14.1 Turning the Unit ON/OFF 10

14.2 Adjusting Speaker Volume 10

14.3 Receiving a Signal 10

14.4 Transmitting a Signal 10

14.5 Changing Channels 11

14.6 CTCSS (Continuous Tone Coded Squelch System) 11

14.7 Monitor 11

14.8 Baby Monitor function 11

14.9 Call Tones 12

14.10 VOX Selection 13

14.11 Squelch level selection 13

14.12 Channel Scan 14

14.13 Dual Channel scan 14

14.14 Automatic Power Off (APO) 15

14.15 Key Tone On/Off 15

14.16 Chronometer 15

14.17 Roger Beep On/Off 16

14.18 Button Lock 16

14.19 Display back light 16

15 Earpiece connection 16

16 Troubleshooting 17

17 Technical specifications 17

18 Service address and hotline support 18

19 Declaration of conformity and manufacturer 18

20 Warranty 18

UCOM Twintalker 4710 DCP 3

UCOM Twintalker 4710 DCP

ENGLISH

20.1 Warranty period 18

20.2 Warranty handling 18

20.3 Warranty exclusions 18

4 UCOM Twintalker 4710 DCP

UCOM Twintalker 4710 DCP

1 Introduction

Thank you for purchasing the UCOM Twintalker 4710. It’s a short range, low powered radio

communication device with a range of maximum 5 Km. It has no running costs other than the

minimal cost of re-charging the batteries.

TheTwinTalker operates on 8 channels.

The Twintalker is protected against vertically falling water drops when enclosure tilted up to

15° according to the IPX2 standard.

2 Intended purpose

It can be used for different professional purposes. For example: support crane operation. It

can be used for recreational purposes. For example: to keep in contact during travelling with

2 or more cars, biking, skiing. It can be used to keep in contact with your children when they

are playing outside, etc...

3CE Mark

The CE symbol on the unit, user guide and giftbox indicates that the unit complies with the

essential requirements of the R&TTE directive 1995/5/EC.

4 Safety instructions

4.1 General

Please read carefully through the following information concerning safety and proper use.

Make yourself familiar with all functions of the device. Keep this manual in a safe place for

future use.

4.2 Burning injuries

• If the cover of the antenna is damaged, do not touch because when an antenna comes

in contact with the skin, a minor burn may result when transmitting.

• Batteries can cause property damage such as burns if conductive material such as

jewellery, keys or beaded chains touches exposed terminals.The material may complete

an electrical circuit (short circuit) and become quite hot. Exercise care in handling any

charged battery, particularly when placing it inside a pocket, purse or other container

with metal objects.

4.3 Injuries

• Do not place your device in the area over an air bag or in the air bag deployment area.

Air bags inflate with great force. If a PMR is placed in the bag deployment area and the

air bag inflates, the communicator may be propelled with great force and cause serious

injury to the occupants of the vehicle.

• Keep the PMR at least 15 centimetres away from a pacemaker.

• Turn your PMR OFF as soon as interference is taking place with medical equipment.

UCOM Twintalker 4710 DCP 5

UCOM Twintalker 4710 DCP

ENGLISH

4.4 Danger of explosion

• Do not replace batteries in a potentially explosive atmosphere. Contact sparking may

occur while installing or removing batteries and cause an explosion.

• Turn your PMR off when in any area with a potentially explosive atmosphere. Sparks in

such areas could cause an explosion or fire resulting in bodily injury or even death.

• Never throw batteries in fire as they may explode.

4.5 Poisoning danger

• Keep batteries away from small children.

4.6 Legal

• In some countries it is prohibited to use your PMR while driving a vehicle. In this case

leave the road before using the device.

• Turn your PMR OFF when on board an aircraft when instructed to do so. Any use of the

PMR must be in accordance with airline regulations or crew instructions.

• Turn your PMR OFF in any facilities where posted notices instruct you to do so.

Hospitals or health care facilities may be using equipment that is sensitive to external RF

energy.

• Replacing or modifying the antenna may affect the PMR radio specifications and violate

the CE regulations. Unauthorised antennas could also damage the radio.

4.7 Notes

• Do not touch the antenna while transmitting, it could affect the range.

• Remove the batteries if the device is not going to be used for a long period.

5 Cleaning and maintenance

• To clean the unit, wipe with a soft cloth dampened with water. Don’t use a cleaner or

solvents on the unit; they can damage the case and leak inside, causing permanent

damage.

• Battery contacts may be wiped with a dry lint-free cloth.

• If the unit gets wet, turn it off and remove the batteries immediately. Dry the battery

compartment with a soft cloth to minimize potential water damage. Leave the cover off

the battery compartment overnight or until completely dry. Do not use the unit until

completely dry.

Areas with potentially explosive atmospheres are often, but not always,

clearly marked. They include fuelling areas such as below deck on

boats, fuel or chemical transfer or storage facilities; areas where the air

contains chemicals or particles, such as grain, dust or metal powders;

and any other area where you would normally be advised to turn off

your vehicle engine.

6 UCOM Twintalker 4710 DCP

UCOM Twintalker 4710 DCP

6 Disposal of the device (environment)

At the end of the product lifecycle, you should not throw this product into the

normal household garbage but bring the product to a collection point for the

recycling of electrical and electronic equipments. The symbol on the product,

user guide and/or box indicate this.

Some of the product materials can be re-used if you bring them to a recycling point. By re-

using some parts or raw materials from used products you make an important contribution to

the protection of the environment. Please contact your local authorities in case you need

more information on the collection points in your area.

7 Using a PMR device

To communicate between PMR devices they need to be set all on the same channel and

CTCSS code and within receiving range (up to max. 5 km in open field). Since these devices

use free frequency bands (channels), all devices in operation share these channels(total 8

channels). Therefore, privacy is not garanteed. Anybody with a PMR set to your channel can

overhear the conversation. If you want to communicate (transmitting a voice signal) you

need to press the PTT-button .

Once this button pressed, the device will go into transmit mode and you can speak into the

microphone. All other PMR devices in range , on the same channel and in standby mode (not

transmitting) will hear your message. You need to wait until the other party stops transmitting

before you can reply to the message. At the end of each transmission the unit will send a

beep if the Roger Beep is enable (see chapter 14.17). To reply, just press the PTT-button

and speak into the microphone.

8 Included in the package

• 2 x Twintalker 4710

• 2 x Beltclip

• 1 x Duo Charger

• 1 x Power adapter

• 2 x NiMH (3 x AAA) battery pack

• 2 x Earpiece with microphone and PTT button

•User guide

• Card with service address and Hotline

If 2 or more users press the PTT- button at the same time the receiver

will receive only the stongest signal and the other signal(s) will be

supressed. Therefore you should only transmit a signal (press PTT-

button ) when the channel is free.

UCOM Twintalker 4710 DCP 7

UCOM Twintalker 4710 DCP

ENGLISH

9 Getting started

9.1 Installing/Removing the Belt

Clip

1. To install the belt clip, align the pin with

the hole in the backside. Gently push

until it clicks into position.

2. To remove the belt clip from the unit,

push the belt clip (A), while pulling the

clip away from the unit (B).

9.2 Battery Installation

1. Remove the belt clip (See chapter

9.1.2).

2. Pull the battery cover tab (C) and gently

remove the battery cover.

3. Install the rechargeable battery pack

following the polarity as shown. The

metal contacts (D) should face

outwards from the radio to connect on

the battery door. Or install 3 ‘AAA’

alkaline or rechargeable batteries

following the polarity as shown.

4. Re-install the Battery Cover and Belt

Clip (See chapter 9.1.1).

1 x AAA

8 UCOM Twintalker 4710 DCP

UCOM Twintalker 4710 DCP

10 Charging batteries

11 Battery Charge Level

The BATTERY CHARGE LEVEL is indicated by the number of squares present inside the

BATTERY icon on the LCD Display.

• Battery Full

• Battery 2/3 charged

• Battery 1/3 charged

• Battery empty

When the battery charge level is low, a beep will be heard.

When NiMh battery packs are installed, the desktop

charger provides drop-in charging conveniency

1. Put the desktop charger on a flat surface.

2. Plug the supplied adapter into the electric

socket. Pay attention to the mentioned voltage

and compare this with the indications of the

power supply. Connect the low tension plug at

the end of the cable with the connector

the backside of the desktop charger.

3. Put the PMR in the charger as indicated.

4. The charging LED will turn on if it’s properly

inserted and charging.

It will take about 12 to 14 hours to fully charge the bat-

teries. There is no indication on the display when the

batteries are being charged.

The device can also operate with 3 x AAA NiMh batteries or with 3 x AAA

Alkaline batteries.

3 x AAA batteries cannot be charged with the charger.

UCOM Twintalker 4710 DCP 9

UCOM Twintalker 4710 DCP

ENGLISH

12 Description

See folded cover page - Illustration 1

13 LCD Display information

See folded cover page - Illustration 2

15. Baby monitor icon

16. VOX icon

17. CTCSS code

18. Key Tone icon

19. Chronometer icon

20. Auto Power Off icon

21. Roger Beep icon

22. Volume icon

23. Key pad lock icon

24. Squelch Level indication

25. Call Tone icon

26. a. Scan icon

b. Dual Scan icon

27. Channel number / Volume level indication

28. Battery level indication

29. RX icon.

– Displayed when receiving

30. TX icon.

– Displayed when transmitting

1. TX LED

– Burns during transmission

2. Antenna

3. LCD Display

4. Earpiece connector

5. MENU button

– Enter the setting menu

6. DOWN button

– Decrease the speaker volume

– Select the previous value in the

menu.

7. CALL button

8. Speaker

9. SCAN/MONITOR button

10. Microphone

11. UP button

– Increase the speaker volume

– Select the next value in the menu.

12. Lock button

13. PUSH TO TALK button PTT

14. ON-OFF button

10 UCOM Twintalker 4710 DCP

UCOM Twintalker 4710 DCP

14 Using the Twintalker 4710

14.1 Turning the Unit ON/OFF

14.2 Adjusting Speaker Volume

14.3 Receiving a Signal

The unit is continuously in the RECEIVE mode when the unit is switched ON and not

transmitting.

14.4 Transmitting a Signal

To turn ON:

• Press and hold the - button for 2 seconds. The unit will

“beep” and the LCD display will display the current channel.

To switch OFF:

• Press and hold the - button for 2 seconds. The unit will

“beep” and the LCD display will turn blank.

• Press the - button in stand-by-mode to increase the

speaker volume. The volume level is displayed.

• Press the - button to decrease the speaker volume.

• Press and hold the PTT - button

to TRANSMIT. The TX

symbol is displayed.

• Hold the unit in a vertical position with the MICROPHONE 10cm

from the mouth and speak into the microphone.

• Release the PTT - button when you want to stop

transmitting.

In order for other people to receive your transmission, they must also be

on the same channel and have set the same CTCSS code. (See chapter

14.5 and 14.6)

To check the channel activity use the monitor function (See chapter

14.7). The maximum transmitting time is limited to 1 minute. Release and

press PTT - button to restart transmitting.

UCOM Twintalker 4710 DCP 11

UCOM Twintalker 4710 DCP

ENGLISH

14.5 Changing Channels

14.6 CTCSS (Continuous Tone Coded Squelch System)

The 2 digit CTCSS code corresponds to a specific tone frequency the radio emits. Two users,

with the same channel and CTCSS set can hear one another.They will not be able to hear

anyone else on the channel unless the other radios have the same exact CTCSS code

enabled. The Twintalker 4710 has 38 CTCSS codes available.

14.7 Monitor

You can use the monitor feature to check for weaker signals in the current channel.

• Press and hold the -button to activate channel monitoring.

• Release the -button to stop monitoring.

14.8 Baby Monitor function

One of the units can be set as Babymonitor. The radio will transmit a signal when it is

activated by the crying baby or another sound in the room (VOX).

The PMR will no longer be able to receive signals to avoid that your baby is disturbed during

his sleep.

The other PMR must be set to the same channel and CTCSS code to receive the signal from

the Baby Monitor.

• Press the - button once, the current channel number

flashes on the display.

• Press the - button or the - button to change the

channel.

• Press the PTT - button

to confirm and return to stand-by

mode.

• Press the - button twice, the current CTCSS code

flashes on the display.

• Press the - button or the - button to change to

another code.

• Press the PTT - button

to confirm and return to stand-by

mode.

If no button is pressed within 5 seconds during setting, the unit will return

to standby.

• Any PMR set on the same channel can receive and listen to the

conversation, also when the other use a CTCSS code.

• To disable CTCSS code, set the code to ‘0’.

12 UCOM Twintalker 4710 DCP

UCOM Twintalker 4710 DCP

To set the PMR as the Baby Monitor:

To deactivate the Baby Monitor:

14.9 Call Tones

A call tone alerts others that you want to start talking.

14.9.1 Setting the Call Tone

The Twintalker 4710 has 10 call tones

14.9.2 Sending a call Tone

Press the button briefly. The call tone will be transmitted on the set channel.

• Press the - button three times, the current Baby Vox

setting flashes on the display and the BABY icon is displayed.

• Press the - button to turn the BABY MONITOR function

ON. Use the - button and the - button to select the

VOX sensitivity level (1 to 3) which displayed.

• Press the PTT - button to confirm and return to stand-by

mode.

• In stand-by, press the - button

three times, the current

Baby Vox setting flashes on the display and the BABY icon is

displayed.

• Press the - button until ‘OF’ appears on the display, to

turn the babymonitor off.

• Press the PTT - button to confirm and return to stand-by

mode.

• Press the - button four times, is displayed.

• Press the - button or the - button to change to

another Call Tone. Select ‘OF’ to disable the call tones.

• Press the PTT - button to confirm and return to stand-by

mode.

In Baby Monitor mode, different functions are disabled (accept Button

Lock, Menu and On/Off function). Only when the Baby Monitor mode is

disabled, all functions can be used again.

If in Baby Monitor mode an earpiece is plugged in, then the Baby Monitor

mode will be disabled when pressing the PTT - button .

UCOM Twintalker 4710 DCP 13

UCOM Twintalker 4710 DCP

ENGLISH

14.10 VOX Selection

The PMR is capable of voice activated (VOX) transmission. In VOX mode, the radio will

transmit a signal when it is activated by your voice or other sound around you. VOX operation

is not recommended if you plan to use your radio in a noisy or windy environment.

14.11 Squelch level selection

The adjustable Squelch allows you to optimise the radios sensitivity. It also allows you to

increase the sensitivity and receive weaker signals.

There are 4 decreasing levels of sensitivity. 1 is the most sensitive, for detecting the weakest

signals. 4 is the least sensitive, for hearing only stronger signals and cutting out

interference from weak signals.

At higher sensitivity settings it is normal to hear occasionally background static noise.

• Press the - button five times, the current VOX setting

flashes on the display and the VOX icon is displayed.

• Press the -button to turn the VOX feature ON. Press the

-button again to set the VOX sensitivity level between 1

and 3. Press the button until ‘OF’ appears on the display,

to turn VOX OFF.

• Press the PTT - button to confirm and return to stand-by

mode.

• Press the - button six times, the current Squelch Level

flashes on the display.

• Press the - button or the - button to change to

another Squelch Level

• Press the PTT - button to confirm and return to stand-by

mode.

• When you use the PMR with the supplied earpiece (See chapter 15),

the VOX function will be disabled as soon as you plug in the

earpiece connector.

• VOX mode will be disabled when you press the PTT - button .

14 UCOM Twintalker 4710 DCP

UCOM Twintalker 4710 DCP

14.12 Channel Scan

Channel scan performs searches for active signals in an endless loop from channel 1 to 8

including the CTCSS codes.

14.13 Dual Channel scan

In stand-by, the PMR is set on one set channel with CTCSS code. The PMR will only receive

signals transmitted on that channel and CTCSS code.

Dual Channel Monitor allows you to monitor a second channel with CTCSS code.

Press the -button seven times to disable the function. Then press the - button

or the - button until ‘OF’ is displayed.

When the Dual Channel Monitor function is activated, the PMR will switch sequentially

between the standby channel + CTCSS and the Dual Channel + CTCSS.

When there is activity on the Dual Channel + CTCSS, the active channel will be displayed

for 5 seconds after the activity has ended. Within this period, you have the posibility to answer

the transmission.

• Press the - button briefly to activate Channel Scan. The

channel scan icon is displayed.

• When an active signal (one of 8 channels) is detected, press the

PTT - button to fix the channel and starts communicating

over the active channel. If you don’t press the PTT - button ,

Channel Scan will restart after 5 seconds.

• Press the - button or the - button to bypass the

current channel and continue to search for another active

channel.

• Press the - button briefly to deactivate Channel Scan.

• Press the - button seven times, the dual channel scan

icon appears on the display.

• Press the - button or the - button to change the

channel.

• Press the - button to confirm the channel selection and

go to CTCSS SUB-CHANNEL SELECTION.

• Press the - button or the - button to change the

CTCSS.

• Press the PTT - button to confirm and return to stand-by

mode.

• When you start the Channel Scan function when your CTCSS - code

is set to ‘0’, the PMR will search for all signals (with or without

CTCSS - code).

• When you start the Channel Scan function when you have set a

CTCSS - code (1 - 38), the PMR will only search for signals with

CTCSS - code. Signal without CTCSS - code will be ignored.

UCOM Twintalker 4710 DCP 15

UCOM Twintalker 4710 DCP

ENGLISH

14.14 Automatic Power Off (APO)

To save energy, you can activate the Automatic Power Off function. In case you forgot to

Power Off the unit, it will switch Off automatically after the set time.

14.15 Key Tone On/Off

When a button is pressed, the unit will beep briefly.

14.16 Chronometer

The Twintalker 4710 has a chronometer function (mm:ss).

• Press the - button eight times, the current Power OFF

time flashes on the display.

• Press the - button or the - button to change to

another time (1 - 12 hour). Select ‘OF’ to disable the APO

feature.

• Press the PTT - button to confirm and return to stand-by

mode.

• Press the - button nine times, the current Key Tone

setting flashed on the display.

• Press the - button or the - button to enable (ON) or

disable (OF) the Key Tone.

• Press the PTT - button to confirm and return to stand-by

mode.

• Press the - button ten times. The counter is displayed.

• Press the - button to start counting.

• Press the - button again to stop counting and see the lap

time. The counter continues in the background. Press the -

button to proceed counting.

• When the counter is stopped, press the - button to reset

the counter.

After selecting this function, and also after resetting the counter, the

measurement should be started within 5 seconds. If not, the device shall

return to stand-by.

16 UCOM Twintalker 4710 DCP

UCOM Twintalker 4710 DCP

14.17 Roger Beep On/Off

After the PTT - button is released, the unit will send out a roger beep to confirm that you

have stopped talking.

14.18 Button Lock

14.19 Display back light

To activate the backlight of the LCD display, press any button except the PTT- button or

the button .

The LCD backlight will light up for 5 seconds.

15 Earpiece connection

The Twintalker 4710 can be used with the included earpiece.

The connector is located under the protective rubber cover on the right side of the unit

To attach the earpiece, remove the rubber flap to expose the connector.

Insert the earpiece plug into the connector (2,5mm jack).

The small button on the earpiece has the same function as the PTT button on the unit

When you use the PTT - Button from the Earpiece, you must also use the microphone from

the earpiece wire.

• Press the - button eleven times, the current Roger Beep

setting flashes on the display.

• Press the - button or the - button to enable (ON) or

disable (OF) the Roger Beep.

• Press the PTT- button to confirm and return to stand-by

mode.

• Press and hold the - button for 3 seconds to activate the

Button Lock mode. The Button Lock icon is displayed on the LCD

Screen.

• Press and hold the - button again to deactivate Button

Lock.

The Button Lock is not valid for the - button , the -button

and the PTT- button .

Do not connect other earpieces. This may damage your device.

UCOM Twintalker 4710 DCP 17

UCOM Twintalker 4710 DCP

ENGLISH

16 Troubleshooting

17 Technical specifications

No power Clean the battery contacts with a soft cloth.

Replace the batteries.

No transmission Make sure the PTT - button is pressed

completely before you speak.

Monitor the channel activity and switch to another

channel if the current is used.

No reception Check the speaker volume.

Make sure that you are in the reception range of

the sender and change if necessary your location.

Limited Range and noice during

transmission

The talking range depends on the terrain.

Steal constructions, concrete buildings or the use

in vehicles have a bad influence on the range.

Try to avoid as many obstacles as possible and

communicate in a clear line of sight.

Change your locations.

Interference The receiver and transmitter are too close. The

mimimum distance between 2 units is 1,5m.

Channels

Sub-code

Frequency

Range

Batteries

Transmission Power

Modulation Type

Channel spacing

Duo Charger adapter

CTCSS 38

446.00625MHz - 446.09375 MHz

Up to 5 Km (Open field)

3 x AAA Alkaline or NiMH rechargeable

=< 500mW ERP

FM - F3E

12,5 kHz

Input : 230V AC / 50Hz

Output : 9V DC / 200mA

Channel Frequency Chart: CTCSS Code Chart

Channel Frequency (MHz

)

Code Frequency (Hz) Code Freq. (Hz) Code Freq. (Hz) Code Freq. (Hz)

1 446,00625 0 Disabled 10 94,8 20 131,8 30 186,2

2 446,01875 1 67,0 11 97,4 21 136,5 31 192,8

3 446,03125 2 71,9 12 100,0 22 141,3 32 203,5

4 446,04375 3 74,4 13 103,5 23 146,2 33 210,7

5 446,05625 4 77,0 14 107,2 24 151,4 34 218,1

6 446,06875 5 79,7 15 110,9 25 156,7 35 225,7

7 446,08125 6 82,5 16 114,8 26 162,2 36 233,6

8 446,09375 7 85,4 17 118,8 27 167,9 37 241,8

8 88,5 18 123,0 28 173,8 38 250,3

9 91,5 19 127,3 29 179,9

18 UCOM Twintalker 4710 DCP

UCOM Twintalker 4710 DCP

18 Service address and hotline support

The service adresses are printed on the extra service card included in the package or can be

found on www.ucom.be.

19 Declaration of conformity and manufacturer

Topcom Europe Nv.

Grauwmeer 17

3001 Heverlee

Belgium

The declaration of conformity can be found on the last page of this user guide.

20 Warranty

20.1 Warranty period

Ucom units have a 36-month warranty period. The warranty period starts on the day the new

unit is purchased. Consumables or defects causing a negligible effect on operation or value

of the equipment are not covered.

The warranty has to be proven by presentation of a copy of the original purchase receipt, on

which the date of purchase and the unit-model are indicated.

20.2 Warranty handling

A faulty unit needs to be returned to an authorized service centre including a valid purchase

note. If the unit develops a fault during the warranty period, the service centre will repair any

defects caused by material or manufacturing faults free of charge.

The service centre will at its discretion fulfil its warranty obligations by either repairing or

exchanging the faulty units or parts of the faulty units. In case of replacement, colour and

model can be different from the original purchased unit.

The initial purchase date shall determine the start of the warranty period. The warranty period

is not extended if the unit is exchanged or repaired by the appointed service centres.

20.3 Warranty exclusions

Damage or defects caused by incorrect treatment or operation and damage resulting from

use of non-original parts or accessories are not covered by the warranty.

The warranty does not cover damage caused by outside factors, such as lightning, water and

fire, nor any damage caused during transportation.

No warranty can be claimed if the serial number on the units has been changed, removed or

rendered illegible.

UCOM Twintalker 4710 DCP 19

UCOM Twintalker 4710 DCP

NEDERLANDS

1 Inleiding 21

2 Gebruiksdoel 21

3 CE-markering 21

4 Veiligheidsinstructies 21

4.1 Algemeen 21

4.2 Brandwonden 21

4.3 Letsel 21

4.4 Explosiegevaar 22

4.5 Vergiftigingsgevaar 22

4.6 Regelgeving 22

4.7 Opmerkingen 22

5 Reiniging en onderhoud 22

6 Afvoeren van het toestel (milieu) 23

7 Een PMR-toestel gebruiken 23

8 De verpakking bestaat uit 24

9Beginnen 24

9.1 De riemclip verwijderen/installeren 24

9.2 Batterijen plaatsen 24

10 Batterijen opladen 25

11 Laadniveau van batterijen 25

12 Beschrijving 26

13 Informatie LCD-display 26

14 De Twintalker 4710 gebruiken 27

14.1 Het toestel in- en uitschakelen (ON/OFF) 27

14.2 Luidsprekervolume afstellen 27

14.3 Een signaal ontvangen 27

14.4 Een signaal zenden 27

14.5 Van kanaal veranderen 28

14.6 CTCSS (Continuous Tone Coded Squelch System) 28

14.7 Monitor 28

14.8 Babymonitorfunctie 29

14.9 Oproeptonen 30

14.10 VOX-selectie 30

14.11 Squelch-niveau selecteren 30

14.12 Kanaalscan 31

14.13 Dual Channel-scan 31

14.14 Automatisch uitschakelen (APO) 32

14.15 Toetstoon in/uitschakelen 32

14.16 Chronometer 33

14.17 Roger-pieptoon in/uitschakelen 33

14.18 Toetsvergrendeling 33

14.19 Achtergrondlicht weergeven 33

15 Aansluiten van een oortelefoon 34

16 Probleemoplossing 34

17 Technische specificaties 35

18 Onderhoudsadres en hotline-ondersteuning 35

19 Verklaring van conformiteit en fabrikant 35

20 Garantie 36

20 UCOM Twintalker 4710 DCP

UCOM Twintalker 4710 DCP

20.1 Garantieperiode 36

20.2 Afwikkeling van garantieclaims 36

20.3 Garantiebeperkingen 36

UCOM Twintalker 4710 DCP 21

UCOM Twintalker 4710 DCP

NEDERLANDS

1 Inleiding

Hartelijk dank voor het aanschaffen van de UCOM Twintalker 4710. Dit is een

radiocommunicatieapparaat met een kort bereik van maximaal 5 km en een laag vermogen.

Er zijn geen gebruikskosten, op de minimale kosten na van het opladen van de batterijen.

De Twintalker werkt met 8 kanalen. Het apparaat kan worden aangewend in elk land waarin

het gebruik is toegestaan, zoals wordt weergegeven op de verpakking en in deze

handleiding.

De Twintalker wordt beschermd tegen verticaal vallende waterdruppels wanneer de

behuizing 15° wordt gekanteld volgens de IPX2-norm.

2 Gebruiksdoel

Het kan worden gebruikt voor verschillende professionele doeleinden. Bijvoorbeeld:

ondersteuning bij kraanwerkzaamheden. Het kan worden gebruikt voor verschillende

recreationele doeleinden. Bijvoorbeeld: om contact te houden wanneer u op reis bent in 2 of

meer voertuigen of tijdens het fietsen of skieën. Ook kunt u hiermee contact houden met uw

kinderen, bv. wanneer zij buiten spelen.

3 CE-markering

De CE-markering op het toestel, de handleiding en de verpakking geeft aan dat het toestel

voldoet aan de basiseisen van de R&TTE-richtlijn 1995/5/EG.

4 Veiligheidsinstructies

4.1 Algemeen

Lees de volgende informatie over de veiligheid en een correct gebruik zorgvuldig door. Stel

u op de hoogte van alle functies van het toestel. Bewaar deze handleiding op een veilige

plaats voor later gebruik.

4.2 Brandwonden

• Raak de antenne niet aan als de afdekking van de antenne is beschadigd, want als een

antenne in contact komt met de huid bij het zenden, kan dit leiden tot kleine

brandwonden.

• Batterijen kunnen schade aan materiaal veroorzaken, bijvoorbeeld brandplekken, als

geleidend materiaal (zoals sieraden, sleutels of kralenkettingen) in aanraking komt met

de blootliggende contacten. Het materiaal kan een elektrisch circuit sluiten (kortsluiting)

en erg heet worden. Hanteer opgeladen batterijen met zorg, vooral als u deze in een

zak, tas of andere houder met metalen voorwerpen plaatst.

4.3 Letsel

• Plaats het toestel niet boven een airbag of in de buurt waar de airbag zich opblaast.

Airbags worden met veel kracht opgeblazen. Als een PMR zich bevindt in de radius van

de airbag op het moment dat deze wordt geactiveerd, kan het toestel met grote kracht

worden weggeslingerd en de inzittenden van het voertuig ernstig verwonden.

• Houd de PMR ten minste 15 centimeter verwijderd van een pacemaker.

• Schakel uw PMR onmiddellijk UIT in geval van interferentie met medische apparatuur.

22 UCOM Twintalker 4710 DCP

UCOM Twintalker 4710 DCP

4.4 Explosiegevaar

• Vervang de batterijen niet in een omgeving waar explosiegevaar bestaat. Bij het

installeren of verwijderen van de batterijen kunnen contactvonken ontstaan, die een

explosie kunnen veroorzaken.

• Schakel uw PMR uit wanneer u zich bevindt in een omgeving waar explosiegevaar

bestaat. Vonken kunnen in een dergelijke omgeving brand of een explosie veroorzaken,

met lichamelijk letsel of zelfs de dood tot gevolg.

• Werp batterijen nooit in vuur, aangezien ze dan kunnen ontploffen.

4.5 Vergiftigingsgevaar

• Houd batterijen uit de buurt van kleine kinderen.

4.6 Regelgeving

• In bepaalde landen is het verboden om onder het rijden uw PMR te gebruiken. Ga in dit

geval aan de kant staan voordat u het toestel gebruikt.

• Schakel uw PMR UIT aan boord van een vliegtuig wanneer u hierom wordt verzocht.

Gebruik van de PMR dient in overeenstemming te zijn met de voorschriften van de

luchtvaartmaatschappij of de instructies van de bemanning.

• Schakel uw PMR UIT op plaatsen waar waarschuwingsbordjes u vragen dit te doen.

Ziekenhuizen of gezondheidscentra kunnen apparaten gebruiken die gevoelig zijn voor

van buitenaf komende radiofrequentie-signalen.

• Het vervangen of wijzigen van de antenne kan de PMR-radiospecificaties beïnvloeden

en inbreuk maken op de CE-voorschriften. Niet-goedgekeurde antennes kunnen ook de

radio beschadigen.

4.7 Opmerkingen

• Raak de antenne niet aan tijdens het zenden; dit kan het bereik beïnvloeden.

• Verwijder de batterijen als u het toestel langere tijd niet gebruikt.

5 Reiniging en onderhoud

• Reinig het toestel met een vochtige doek. Gebruik hiervoor alleen water. Gebruik geen

reinigings- of oplosmiddelen op het toestel; deze kunnen de behuizing beschadigen en

naar binnen lekken, wat kan leiden tot blijvende beschadigingen.

• Gebruik een droge, pluisvrije doek om de batterijcontacten te reinigen.

• Schakel het toestel direct uit en verwijder de batterijen wanneer het toestel nat is

geworden. Droog het batterijvak met een zachte doek om mogelijke waterschade tot

een minimum te beperken. Laat het afdekplaatje van het batterijvak een nacht lang open

of totdat het volledig droog is. Gebruik het toestel niet voordat dit volledig droog is.

Omgevingen waar explosiegevaar bestaat zijn vaak, maar niet altijd,

duidelijk aangegeven. Hieronder vallen brandstoftankruimtes, zoals

onderdeks op schepen, overslag- of opslagplaatsen voor brandstof of

chemicaliën; omgevingen waar de lucht chemicaliën of deeltjes bevat,

zoals graan, stof of metaaldeeltjes; en elke andere omgeving waar u

gewoonlijk wordt geadviseerd de motor van uw voertuig uit te schakelen.

UCOM Twintalker 4710 DCP 63

UCOM Twintalker 4710 DCP

DEUTSCH

12 Beschreibung

Siehe Abbildung 1 auf der ausklappbaren Umschlagseite

13 LCD Display Informationen

Siehe Abbildung 2 auf der ausklappbaren Umschlagseite

15. Babyfon-Symbol

16. VOX-Symbol

17. CTCSS-Code

18. Anrufton-Symbol.

19. Chronometer-Symbol

20. Symbol für automatisches Abschalten

21. Quittungston-Symbol

22. Lautstärke-Symbol

23. Tastensperre-Symbol

24. Rauschunterdrückungsanzeige

25. Anrufton-Symbol

26. a. Scan-Symbol

b. Dual Scan-Symbol

27. Kanalnummer / Lautstärkeanzeige

28. Batteriezustandsanzeige

29. RX-Symbol.

– Wird beim Empfang angezeigt

30. TX-Symbol.

– Wird beim Übertragen angezeigt

1. TX LED

– Leuchtet bei der Übertragung

2. Antenne

3. LCD Display

4. Anschlussbuchse für Kopfhörer

5. MENÜ-Taste

– Öffnet das Einstellmenü

6. NACH-UNTEN-Taste

– Verringern der

Lautsprecherlautstärke

– Auswahl des vorigen Menüpunkts.

7. RUF-Taste

8. Lautsprecher

9. SCAN/MONITOR-Taste

10. Mikrofon

11. NACH-OBEN-Taste

– Erhöhen der Lautsprecherlautstärke

– Auswahl des nächsten Menüpunkts.

12. Tastensperre-Taste

13. DRÜCKEN UM ZU SPRECHEN-Taste

PTT

14. EIN-AUS-Taste

Kde sa dá kúpit kryt na anténu z umelej hmoty typ,,, Twintalker 4710 DCP , Submitted on 30-3-2023 at 14:28
Reply Report abuse
batteries required for two ucom twintalker 4710 combi pack Submitted on 11-5-2019 at 16:18
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Topcom Twintalker 4710 Duo Combi Pack in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Topcom Twintalker 4710 Duo Combi Pack Manual

Product: