640724

Topcom KS-4240 BABYVIEWER Manual

5
Zoom out
Zoom in
Previous page
1/98
Next page
5
Babyviewer - KS-4240
ENGLISH
®
9 Installing the Babyviewer KS-4240
9.1 Fine tuning
• Place the camera in a convenient location, point the lens of
the camera to the observation area.
• Adjust the angle by rotation the camera.
10 Operation and use
10.1 Switching the baby unit and parent unit on
and off
– Press the on/off button to switch on the parent
unit. The display is activated.
– Slide the on/off switch up to switch on the baby
unit. The on/off LED is activated.
– Press the on/off button to switch off the parent
unit (press and hold until the display goes blank).
– Slide the on/off switch down to switch off the
baby unit.
10.2 Baby phone mode.
The Babyviewer can also be used as a audio babyphone, this is
an option to save energy. Follow the procedure below.
– Make sure the VOX mode is off, see the VOX paragraph
for instructions (See “10.13 Voice activated transmission
(VOX)”).
– Press the on/off button to go to audio
babyphone modus.
– Press the on/off button again to turn on the
display again.
10.3 Checking the connection between the parent
unit and the baby unit
You should always check the wireless connection when you use
the babyphone for the first time.
– Put the parent unit in the same room as the baby unit,
separated by at least two meters.
– Switch on both devices. The parent unit will try to
establish a connection with the baby unit.
– The display of the parent unit will show the captured
image from the baby unit after the connection has been
established (monitor mode).
– The sounds picked up by the microphone are
reproduced by the parent unit.
– The volume of the reproduced sound is indicated by the
volume LED’s at the top of the parent unit.
The higher the volume, the more LED’s are on.
– If no connection is established, “OUT OF RANGE” is
displayed.
10.4 Out of range indication
The maximum range between the parent- and baby unit is 300
meter in open area. Different factors, such as bricks and plaster
walls, will reduce the range. Moreover, reinforced concrete floors
will influence the range tremendously.
In a residence, normal operating range is up to 50 meters and 2
floors.
– If the connection is interrupted, “OUT OF RANGE” is
displayed.
– Reduce the distance between the parent and baby units
until a new connection is established.
10.5 Setting the reproduction volume of the
parent unit
There are 5 volume levels.
– Press button to increase the volume.
– Press button to decrease the volume.
10.6 Setting the parent unit display brightness
When the display in on.
– Press the menu button once. The Brightness
icon is displayed.
– Press the up or down button to select the
desired brightness (5 steps).
– Press the menu button to confirm.
– After 10 seconds the parent unit will switch back to
monitor mode.
10.7 Temperature indication
When the display is on, the baby’s room temperature is displayed
in the right lower corner.
To set the temperature unit:
– Press the menu button twice. The temperature
icon is displayed.
– Press the up or down button to °C
(Celsius), °F (Fahrenheit).
– Press the menu button to confirm.
– After 10 seconds the parent unit will switch back to
monitor mode.
10.8 Temperature alert
You can set a high/low temperature alert, the unit will give beep
when the temperate will go beyond the preset range.
– Press the menu button 3 times to set the highest
temperature between 25°C and 39°C.
– Press the menu button 4 times to set the lowest
temperature between 10°C and 24°C
– You can change the temperature by pressing the up
or down button .
– To turn off the temperature alert, select OFF in both
modes.
10.9 Zoom function
The parent unit has X2 zoom digital view function.
– When parent unit in X1 viewing mode, press and hold
the the menu button for 2 seconds,
– The live viewing area will change to X2 zoom mode
immediately. At the same time, four direction arrows are
displayed at the middle of the screen.
– Press the up button or down button to
move the screen up and down.
– Press the camera button to move the screen to
left
– Press the music button to move the screen to
right
– Press the menu button key to go back to the
monitor mode.
Switch back to X1 viewing mode
– When parent unit is in X2 zoom mode, press and hold
the menu button for 2 seconds.
– X1 magnification icon appears and the screen becomes
X1 viewing mode.
– Press the menu button to go back to monitor
mode
10.10 Talking with your baby
You can use the parent unit to talk with your baby.
– Press the Talk button on the parent unit and hold
it pressed.
– Hold the parent unit vertical with the microphone
approximately 10 cm from your mouth, and speak into
the microphone.
– Release button when you have finished talking.
CAUTION
Do not place the camera and wires within the baby’s reach!
Fix the camera at least 1 meter away from the baby.
The parent unit will try to establish a connection
with the baby unit. If captured image from the
camera is displayed, a connection has been
established.
25
20
4
25
4
25
25
6
14
Allow your baby to get used to the talk function
before you use it in practice.
16
17
23
16 17
23
23
16 17
23
23
23
16
17
23
16 17
19
18
23
23
23
24
24
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Topcom KS-4240 BABYVIEWER at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Topcom KS-4240 BABYVIEWER in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 83,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info