469791
66
Zoom out
Zoom in
Previous page
1/95
Next page
67
Cocoon 300
6767676767
Press the Programming key .
‘BASE _‘ appears on the display.
Enter a number for the base unit to which you would like to subscribe the handset (1-4).
Use the number keypad.
‘SEARCHING’ and the symbol appear on the display.
The RFPI code (each base unit has a unique RFPI code) appears on the display and a signal
sounds once the base unit is found by the handset.
Press the Programming key .
‘PIN’ appears on the display.
Enter the 4-digit PIN code of the base unit (default PIN code is ‘1590’). Use the number keypad.
Press the Programming key .
The handset is subscribed to the base unit.
4.25 Subscribing a Butler 1800T handset to a Cocoon 300 base unit
The below procedure only applies to a Butler 1800T handset and Cocoon 300 base unit!!
Press the Paging key on the base unit for 10 seconds until the Line/Charge indicator
op the base unit starts to blink quickly. The Line/Charge indicator will blink quickly for one
minute. During this minute, the base unit is in subscribing mode and you must do the
following to subscribe the handset:
Press the key once.
Press the OK key and select a base unit (1-4) with the keys.
Press the OK key.
Enter the PIN code of your base unit. Usually: 0000.
Press OK. The Butler 1800T now searches for your DECT base unit. As soon as it finds it, you
will see the identification code of this base unit on the display.
Press OK to confirm your selection or press ESC to cancel the subscription.
4.26 Removing subscription of a handset to a base unit
It is possible to cancel subscription of a handset to a base unit. You would do this if a
handset is damaged and has to be replaced by a new one.
Caution: You can only cancel subscription of another handset, not the handset you are using to do the
cancellation procedure.
Press the Programming key .
Press the Up or Down key repeatedly until ‘SETTING’ appears on the display.
Press the Programming key .
Press the Up or Down key repeatedly until REMOVE HS appears on the display.
Press the Programming key .
‘PIN’ appears on the display.
Enter your 4-digit PIN code in (default PIN code is ‘0000’). Use the number keypad.
Press the Programming key .
‘REMOVE HS’ appears on the display.
Dial the number of the handset you want to remove (1 –5). Use the number keypad.
Press the Programming key .
‘REMOVE HS’ appears on the display and the handset is removed
NOT SUB’ appears on the handset removed.
67
COCOON 300 27/6/01 2:45 pm Page 67
66


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Topcom Cocoon 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Topcom Cocoon 300 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info