298481

Topcom butler 4011 Manual

126
Zoom out
Zoom in
Previous page
1/140
Next page
HANDLEIDING
MODE D’EMPLOI
USER GUIDE
BEDIENUNGSANLEITUNG
MANUAL DE USUARIO
V.1.2
Butler 4011/4011C
HL_B4011_mideur.book Page 1 Tuesday, September 7, 2004 4:49 PM
!! Important !!
To use ‘Caller ID’ (display caller), this service has to be activated on your phone line. Normally you need a
separate subscription from your telephone company to activate this function. If you don’t have the Caller ID
function on your phone line, the incoming telephone numbers will NOT be shown on the display of your
telephone.
!! Belangrijk !!
Om de ‘Nummerweergave’ te kunnen gebruiken, moet deze dienst geactiveerd zijn op uw telefoonlijn. Om
deze dienst te activeren, hebt U hiervoor meestal een apart abonnement van uw telefoonmaatschappij
nodig. Indien U geen nummerweergavefunctie hebt op uw telefoonlijn, zullen de inkomende
telefoonnummers NIET op de display van uw toestel verschijnen.
!! Important !!
Pour utiliser la fonction ‘Caller ID/Clip’ (affichage de l’appelant), ce service doit être activé sur votre ligne
téléphonique. Généralement, vous avez besoin d’un abonnement séparé de votre compagnie de téléphone
pour activer cette fonction. Si vous n’avez pas la fonction ‘Caller ID - Affichage Appelant’ sur votre ligne
téléphonique, les numéros de téléphone entrants n’apparaîtront PAS sur l’écran de votre téléphone.
!! Wichtig!!
Zur Verwendung der ‘Rufnummernanzeige’ muss dieser Dienst erst für Ihre Telefonleitung freigegeben
werden. Zur Aktivierung dieser Dienstleistung benötigen Sie meistens ein separates Abonnement Ihrer
Telefongesellschaft.Wenn Sie für Ihre Telefonleitung keine Rufnummernanzeigefunktion haben, erscheinen
die eingehenden Telefonnummern NICHT im Display Ihres Gerätes.
¡¡ Importante !!
Para poder usar la función “Identificación de llamadas,este servicio tiene que estar dado de alta en su línea
telefónica. Normalmente es necesario abonarse a dicho serviciopara que la compañía telefónica active esta
función. Si su línea telefónica no dispone de la funciónIdentificación de llamadas, la pantalla del aparato no
mostrará los números de teléfono de las llamadas entrantes.
GB
The features described in this manual are published with reservation to modifications.
NL
De in deze handleiding beschreven mogelijkheden worden gepubliceerd onder voorbehoud
van wijzigingen.
F
Les possibilités décrites dans ce manuel sont publiées sous réserve de modifications.
D
Die in dieser Bedienungsanleitung umschriebenen Möglichkeiten, werden vorbehaltlich
Änderungen publiziert.
ES
Las características descritas en este manual pueden ser objeto de futuras modificaciones.
This product is made by Topcom Belgium
GB
To be connected to the public analogue telephone network.
NL
Geschikt voor aansluiting op het openbare analoog geschakelde telefoonnetwerk.
F
Il est destine à ëtre raccordé au réseau de télécommunication public.
D
Kompatibel für den analog telefonanschluss.
ES
Conexión a la red telefónica analógica.
HL_B4011_mideur.book Page 2 Tuesday, September 7, 2004 4:49 PM
Butler 4011/4011C 3
Butler 4011/4011C
ENGLISH
SAFETY INSTRUCTIONS
• Only use the charger plug supplied. Do not use other chargers, as this may damage the
battery cells.
• Only insert rechargeable batteries of the same type. Never use ordinary, non-
rechargeable batteries. Insert rechargeable batteries so they connect to the right poles
(indicated in the battery compartment of the handset).
• Do not touch the charger and plug contacts with sharp or metal objects.
• The operation of some medical devices may be affected.
• The handset may cause an unpleasant buzzing sound in hearing aids.
• Do not place the basic unit in a damp room or at a distance of less than 1.5 m away from
a water source. Keep water away from the handset.
• Do not use the telephone in environments where there is a risk of explosions.
•Dispose of the batteries and maintain the telephone in an environment-friendly manner.
• As this telephone cannot be used in case of a power cut, you should use a mains-
independent telephone for emergency calls, e.g. a mobile phone.
• This telephone uses rechargable batteries. You have to dispose of the batteries in an
environment friendly manner according to your country regulations.
CLEANING
Clean the telephone with a slightly damp cloth or with an anti-static cloth. Never use
cleaning agents or abrasive solvents.
NiMH
The CE symbol indicates that the unit complies with the essential requirements of the
R&TTE directive.
HL_B4011_mideur.book Page 3 Tuesday, September 7, 2004 4:49 PM
4 Butler 4011/4011C
Butler 4011/4011C
1 INSTALLATION
Before you use the telephone for the first time, you must first make sure the battery is charged
for 20 hours. If you do not do this, the telephone will not work optimally.
1.1 BASE
For installation, do the following:
•Plug one end of the adaptor into the outlet and the other end into the adapter jack on the
bottom of the telephone.
• Connect one end of the telephone cord with the wall phone jack and the other end to the
bottom of the telephone.
1.2. CHARGER
(only in Twin, Triple or Quatro pack)
• connect the ac adaptor to the electric socket
telephone connection
adapter outlet wall phone jack
adapter jack
HL_B4011_mideur.book Page 4 Tuesday, September 7, 2004 4:49 PM
Butler 4011/4011C 5
Butler 4011/4011C
ENGLISH
1.3. HANDSET
• Open the battery compartment (see below).
•Insert the batteries
respecting the (+ and -) polarity
.
•Close the battery compartment.
• Leave the handset on the base unit for 20 hours. The Line/Charge indicator (LED)
on the base unit will light up.
Battery indicator:
• The battery is fully charged.
• The battery is half drained (50%)
• The battery is low. When the battery is low, you will hear warning signals and the
battery symbol on the display will blink.
2 KEYS/LED
HANDSET BASE
1Display 12 Paging key
2Line key 13 Line/Charge indicator (LED)
3 Up/Handsfree key /
4 Programming key/INT key
CHARGER
5 Phonebook key 14 Charge indicator
6 Redial/Pause key
7Microphone
+-
-+
/P
HL_B4011_mideur.book Page 5 Tuesday, September 7, 2004 4:49 PM
6 Butler 4011/4011C
Butler 4011/4011C
8 Volume/Ringer key /
9Alphanumeric keys
10 Delete/Mute key/Escape key
11 Down/Flash key /
R
23 Messages/answering ON-OFF LED
24 Answering machine key
25 Microphone
26 Speaker
Butler 4011
12
13
BASE
R
/OK
Esc INT
*
#
7
PQRS
4
GHI
2
ABC
5
JKL
8
TUV
0
3
DEF
6
MNO
9
WXYZ
1
Butler 4011C
1
3
4
2
9
6
7
8
10
11
5
14
CHARGER
HANDSET
HL_B4011_mideur.book Page 6 Tuesday, September 7, 2004 4:49 PM
Butler 4011/4011C 7
Butler 4011/4011C
ENGLISH
3 DISPLAY (LCD)
1 Number of calls received.
2 Date (day/month) of calls received.
3Time (hour:minutes) of calls received.
4 Call information.
5 Symbol display ( ):
-this symbol means that the handset is located within the range of the base unit.
- when this symbol starts blinking, this means you are beyond the range of the
base unit. Move closer to the base unit so that the connection between the base unit
and the handset can be restored.
6 Symbol display ( ):
-this symbol means that the telephone has received calls that are automatically
stored in the Call List.
7 Symbol display ( ):
-this symbol means that the mute function is activated, the microphone is turned off
during a conversation.
8 Symbol display ( ):
-this symbol appears on the display when you make or receive a call.
9 Symbol display ( ):
-this symbol means that the ringer is turned off. When you receive a call, the
telephone does not ring. The telephone will ring when you receive an internal call.
10 Symbol display ( ):
-this symbol is the battery indicator.
11 Symbol display ( ):
-this symbol means you are in the menu.
12 Symbol display ( ):
-this symbol appears when you browse the numbers in the Phone Book.
13 Symbol display ( ):
-this symbol appears when you have received a voice mail message (see chapter 6).
14 Symbol display ( ):
2
1
4
3
13 12 11 10 9 7 6 14 5
HL_B4011_mideur.book Page 7 Tuesday, September 7, 2004 4:49 PM
8 Butler 4011/4011C
Butler 4011/4011C
-this symbol means that the handsfree function is activated. You can now talk without
having to pick up the handset.
- Blinks when base telephone is active. You can’t take the line with the handset as
long as base telephone is active!
4 HANDSET OPERATION
4.1 SETTING THE LANGUAGE
The telephone has 14 display languages: see display languages table on packaging!!
To set the language, do the following:
• Press the Programming key .
• Press the Up or Down key repeatedly until ‘SETTING’ appears on the display
• Press the Programming key .
• Press the Up or Down key repeatedly until ‘LANGUAGE’ appears on the display.
• Press the Programming key .
• The language set appears on the display.
• Press the Up or Down key repeatedly to select the language you would like to use.
• Once the desired language appears on the display, press the Programming key to
confirm your selection or repeatedly press the ESC key to leave the menu.
4.2 MAKING CALLS
!!! When making external calls through the handset, base telephone operation is
not possible!!!
4.2.1 External Call
• Press the Line key .
• The Line/Charge indicator (LED) on the base unit will blink. ‘EXT’ and the Call
symbol appear on the display.
• You will hear the dial tone. Dial the telephone number you wish to call.
• The number appears on the display and is dialled.
•After finishing your call, press the Line key to hang up.
4.2.2 Number preparation
•Dial the telephone number you wish to call. You can correct the number by pressing the
Delete/Mute key .
• Press the Line key .
• The Line/Charge indicator (LED) on the base unit will blink. ‘EXT’ and the Call
symbol appear on the display.
• The telephone number is dialled automatically.
•After finishing your call, press the Line key to hang up.
4.2.3 Redialling the last n
umber dialled
• Press the Line key .
HL_B4011_mideur.book Page 8 Tuesday, September 7, 2004 4:49 PM
126 Butler 4011/4011C
Butler 4011/4011C
Mantenga oprimida durante 10 segundos la tecla localizar en la base hasta que el
indicador de Línea/Carga empiece a parpadear rápidamente en la base. El indicador
de Línea/Carga continuará parpadeando rápidamente durante un minuto.
Durante este intervalo la base permanecerá en el modo asociar y se deberá hacer lo
siguiente para asociar el portátil:
• Pulse la Programar .
• Pulse repetidamente la tecla Arriba o Abajo hasta que aparezca REGIS BASE’
en la pantalla.
• Pulse la Programar .
• Aparecerá BASE en la pantalla.
• Con el teclado numérico introduzca el número de la base a la que le gustaría asociar el
portátil.
Nota: Se puede asociar cada portátil a 4 unidades base DECT diferentes. A cada
base se le asigna un número del 1 a 4 en el portátil. Cuando se asocia un nuevo
portátil, se le puede asignar un número de unidad base del 1 al 4. Es preferible
asignarle el ‘1’ .
•‘Aparecerá en la pantalla ‘BUSCANDO' y el icono .
• Aparecerá en la pantalla el código RFPI (cada base tiene un código RFPI único) y el
portátil emite una señal acústica cuando encuentra la base.
• Pulse la Programar .
•‘Aparece ‘PIN' en la pantalla.
• Con el teclado numérico introduzca el código PIN de 4 dígitos de la base (el código PIN
predeterminado es el ‘0000').
• Pulse la Programar .
• La unidad portátil se ha asociado a la base.
4.24 ASOCIAR EL PORTÁTIL BUTLER 4011 A OTRA BASE (DE OTRA
MARCA O MODELO)
Seleccione el modo asociar en la base (refiérase al manual de la base). Una vez activado el
modo asociar, haga lo siguiente para asociar el portátil:
• Pulse la Programar .
• Pulse repetidamente la tecla Arriba o Abajo hasta que aparezca 'REGIS BASE’
en la pantalla.
• Pulse la Programar .
• Aparecerá ‘BASE_’ en la pantalla.
• Con el teclado numérico introduzca el número de la base a la que le gustaría asociar el
portátil (1-4).
• Aparecerá en la pantalla ‘BUSCANDO' y el icono .
• Aparecerá en la pantalla el código RFPI (cada base tiene un código RFPI único) y el
portátil emite una señal acústica cuando encuentra la base.
• Pulse la Programar .
• Aparece ‘PIN' en la pantalla.
• Con el teclado numérico introduzca el código PIN de 4 dígitos de la base (el código PIN
predeterminado es el ‘0000').
• Pulse la Programar .
• La unidad portátil se ha asociado a la base.
HL_B4011_mideur.book Page 126 Tuesday, September 7, 2004 4:49 PM
… 126 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Topcom butler 4011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Topcom butler 4011 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info