462217

Topcom Butler 2800 Manual

10
Zoom out
Zoom in
Previous page
1/44
Next page
10 Topcom Butler 2800
Topcom Butler 2800
• Press and hold the and key for 3 sec.
• The following will appear on the display:
• Enter the number of the base unit you would like to subscribe the handset to (1-4)
• The unit will start searching for the base and when found it will ask to enter the pin code (4 digits):
• Enter the base pin code (0000). If the pin is wrong, the handset will restart the searching for the base.
•When the handset is registered, it will show ‘HS’ followed by the handset number.
7.2 SUBSCRIBING A TOPCOM BUTLER 300 DECT GAP HEADSET
Press the Paging key on the base unit for 10 seconds until the Line/charge indicator on the base unit starts to blink
quickly. The line/charge indicator will blink quickly for one minute. During this minute, the base unit is in subscribing
mode and you must do the following to subscribe the headset:
- Turn ON the headset by pressing the ON/OFF button until you hear two beep tones. At the same time the red and
green LED will lit ones.
- Remove the rubber cover of the power socket so that the hole of the power socket is free. Pull out the rubber cover
from the headset so that the registration key hole is free also.
- Press the headset registration key. The red LED will flash rapidly.
- If after a few seconds the green LED flashes slowly, the registration is successful.
- If the red LED flashes slowly, the registration is failed. Repeat above procedure.
7.3 REMOVING A HANDSET
You can remove a handset from a base to allow another handset to be registered:
• Press and hold the mute and redial key for 3 sec.
• Enter the pin code (0000). If the pin is wrong, the handset will go back to standby.
• Enter the handset number (1-5) you want to remove
• The unit will go back to standby is the removal is successfully. If not, it will ask again to enter the handset number
Remark: You can only remove existing handsets and others then the one you are using
PIN
PIN 1234 H5-
H L _ B 2 8 0 0 . b o o k Page 10 Friday, August 29, 2003 1:16 PM
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Topcom Butler 2800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Topcom Butler 2800 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info