462213

Topcom Butler 200 Manual

27
Zoom out
Zoom in
Previous page
1/46
Next page
4.2. REAR VIEW
1. Connection adaptor
2. Connection telephone line
5. GENERAL
With cordless telephones, radio connection replaces the cord connecting the handset
to the base unit of traditional telephones. This allows you to make and receive calls
even when you are away from the base unit. Thanks to this radio connection, your
mobility increases.
The Butler 200 has a working range of 300 m (range is reduced to 50 m inside
buildings). This working range is however strongly reduced if there are several obsta-
cles between the base and the handset. If you have gone too far away from the base,
you will hear a warning signal. Go back in the range within 10 seconds, otherwise the
connection will be broken. When the radio connection between the handset and the
base station is not possible, you will hear an intermittent tone. Move closer to the
base station so that the radio connection can be established.
6. INSTALLATION
1. Connect the telephone cord to the left socket on the rear of the base (rear of base
facing you) and plug the other end into the line wall socket.
2. Connect the power cable plug to the power socket on the right side of the rear of
the base (rear of base facing you) and plug the adaptor into a power socket.
7. BATTERY
Open the cover of the battery compartment on the backside of the handset. Connect
the battery to the connector in the battery compartment of the handset and close the
battery compartment again afterwards.
The battery of the handset needs to be charged before telephone calls can be made.
In order to have a fluent use of your cordless telephone, we would like to advise you
to proceed as follows:
To charge a new battery (speed charge procedure):
- Place the handset in the connected base station.
- Press and hold the paging button on the base station during 5 seconds until you
hear a beep. To make sure that the beep is audible, set the ring volume switch of
the base station in the maximum position.
- The battery is now charged at a high speed.
- After approximately 6 hours the battery indicator on the base station will blink
and the handset is fully charged.
To charge the battery after normal use:
The charging time of the battery depends on the number of calls made, which are
registered by the unit.
- Place the handset in the connected base station.
- When the battery indicator on the base station blinks, the handset is fully charged
(the charging time of an empty battery= 11 hours).
Do not put the handset back in the base station, every time the phone has been used.
Put the handset only on the base when it is indicated that the battery is almost empty.
It is better for the battery to be sufficiently discharged before being charged again.
You will hear an intermittent beep and the low battery indicator on the display of the
handset will blink.
A fully charged battery allows a talk time of 5 hours. In standby mode the battery has
to be recharged after approximately 50 hours .
R e m a r k s :
· The charger contacts of the handset should not come into contact with metal since
this could cause a short-circuit and damage the battery irreparably.
· The charger contacts of the battery on the base station and on the handset should
be cleaned with a soft cloth once a month.
8
9
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Topcom Butler 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Topcom Butler 200 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info