531049

Topcom BABYTALKER 3500 Manual

12
Zoom out
Zoom in
Previous page
1/196
Next page
Babytalker 3500 SEDS
12
11.2 Problem Causes and Solutions
The following table is intended to help you localise and solve minor problems.
11.3 Registering the Parent Unit with the Baby Unit
If the night light of the baby unit blinks and/or no connection can be established between the parent unit and the
baby unit (blinking green LED on the parent unit), the parent unit needs to be registered with the baby unit.
– Unplug the AC mains adapter of the baby unit from the mains receptacle and remove the batteries from
the parent unit.
– Press the On/Off switch of the baby unit and hold it pressed while plugging the AC mains adapter into
the mains receptacle.
The baby unit will start up in registration mode.
– Release the On/Off switch . The night light of the baby unit will blink for 60 seconds.
– Press the On/Off switch of the parent unit and hold the button pressed while installing the batteries.
The parent unit will start up and the 2 red volume LEDs will blink. Release the On/Off switch .
CAUTION
Risk of hazard due to incorrect repairs
Incorrect repairs can expose users to serious hazards and cause damage to the equipment.
• Never attempt to modify or repair the equipment.
• Always have repairs to equipment or cables performed by a specialist or the service centre.
• If you suspect that the equipment is damaged (for example, if it has fallen on the floor), have it
checked by a specialist before you use it again.
Problem Possible cause Solution
The rechargeable
battery pack of the
parent unit does not
charge
Charging station plug not connected Connect plug
Dirty contacts Clean the battery terminals and
charging station contacts with a soft
cloth
The rechargeable battery pack is
defective
Replace the battery pack
Parent unit does not
switch on (display
remains blank)
The rechargeable battery pack is not
charged
Charge the battery pack
Equipment defective Contact customer service
‘NOT LINKED’ appears
on the parent unit
display
Baby unit not switched on Switch on the baby unit
The parent unit and baby unit are too
far apart
Reduce the distance between the
parent unit and the baby unit
The parent unit is not registered with
the baby unit
Register the parent unit with the baby
unit (see “11.3 Registering the Parent
Unit with the Baby Unit”
The parent unit does
not reproduce the
sounds picked up by
the baby unit
The volume setting of the parent unit
may be too low or switched off.
Increase the volume setting of the
parent unit
The microphone sensitivity of the baby
unit may be set too low.
Check the VOX sensitivity and the
volume setting of the parent unit and
increase if necessary.
Limited range and
interference during
transmission
The range of the equipment depends
on the surroundings.
Steel structures and concrete walls
can impair transmission.
Avoid obstacles as much as possible.
The equipment emits a
high-pitched whistle
The parent unit and baby unit are too
close together
Increase the distance to at least
2 metres
• Check that the AC mains adapter of the baby unit is connected and plugged into a mains
receptacle and that the batteries in the parent unit are charged.
21
12
12
2
29
17
29
Babytalker 3500 SEDS D106.book Page 12 Tuesday, November 10, 2009 1:16 PM
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Topcom BABYTALKER 3500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Topcom BABYTALKER 3500 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info