Manual Toolson TS6000 PRO (page 22 of 200) (English, German, Dutch, Danish, French, Italian, Swedish, Turkish, Spanish, Norwegian, Finnish)

782529

Zoom out

Zoom in

1/200

22 І 200

Saw blade assembly/replacement (Fig. 9/12/13)

1. Warning! Disconnect the mains supply and wear

safety gloves.

2. Disassemble the saw blade guard (2) (Fig. 12).

3. Remove the table insert (6) (Fig. 9).

4. Loosen the nut by placing the open-ended spanner

(f) on the nut and countering with another open-

ended spanner (f) on the ange (Fig. 13).

5. Warning! Turn the nut in the rotational direction of

the saw blade.

6. Remove the outer ange and pull the old saw blade

from the inner ange, with a diagonally downwards

movement.

7. Carefully clean the saw blade ange with a wire

brush before xing the new saw blade.

8. Insert the new saw blade in reverse order and

tighten it.

Warning! Observe the rotational direction; the

teeth have to point in the direction of rotation,

i.e. forwards.

9. Attach the table insert (6) and the saw blade guard

(2) again and set them.

10. Before working with the saw again, check the func-

tionality of the guards.

Using the saw

On/Off switch (Fig. 14)

- The saw can be switched on by pressing the green

pushbutton (11) „I“.

- The red pushbutton (11) „0“ has to be pressed to

switch off the saw.

Cutting depth (Fig. 14)

Turn the round handle (8) to set the blade to the re-

quired cutting depth.

- Turn anti-clockwise: larger cutting depth

- Turn clockwise: smaller cutting depth

After each new adjustment it is advisable to carry out a

trial cut in order to check the set dimensions.

Setting the angle (Fig. 14)

With the table saw you can make diagonal cuts to the

left oriented to the stop bar from 0 ° to 45 °.

m Check before each cut, that between the stop bar

(e), cross-stop (13) and the saw blade (5) a collision is

not possible.

- Loose the xing handle (9).

- Set the required angle on the scale.

- Lock the xing handle (9) again in the required angle

position.

Working with the rip fence

Setting the fence height (Fig. 15)

- The fence rail (25) of the rip fence (7) has two guiding

surfaces with different heights.

- Depending on the thickness of the material to be cut,

the higher side of the fence rail (25) has to be used

for thick material (work piece thickness above 25 mm)

and the lower side of the fence rail for thin material

(work piece thickness below 25 mm).

- For the adjustment, loosen the bolts on the side of the

rip fence (7) and push the fence rail (25) on the guide,

depending on the required position.

- Tighten the bolts again.

Note: If compounds with a bolt (round head / or hexa-

gon), hex nuts and washers are backed up, the washer

must be tted under the nut.

Insert screws each from outside to inside. Secure con-

nections with nuts on the inside.

Note: Tighten the nuts and bolts during assembly only

to the extent that they can not fall down.

If you tighten the nuts and bolts prior to nal assembly,

nal assembly can not be performed.

Frame assembly, Fig. 5/6/7

1. Fix the four legs (17) with the bolts (g) and nuts (h)

to the struts (20+21).

m Warning!

The top struts are equipped with a slot for xing

them to the table!

Ensure that markings A and B are always opposite

each other.

2. Now loosely x the lower struts to the legs using the

bolts (g) and nuts (h) (Fig. 5).

3. Now place the rubber feet (22) on the legs (Fig. 6).

4. Then mount the entire saw on the frame by xing

the hexagon head bolts and the nuts in the corners

(Fig. 7).

5. Afterwards, tighten all bolts and nuts to the frame.

Hand wheel assembly, Fig. 8

1. Place the washer (a) on the bolt (e).

2. Then place the bolt on the handle (d) and the

washer (c) on the bolt.

3. Fix the whole assembly to the hand wheel (8) and

secure it with the hex-nut (b).

Riving knife set-up (Fig. 9/10/11)

m Warning! Disconnect the mains cable!

The set-up of the riving knife (6) must be checked

before each use.

1. Set the saw blade (5) to the max. cutting depth, put

it in the 0° position and lock it. .

2. Remove the table insert (6) (Fig. 9)

m Warning! For transport reasons, the riving

knife (6) was xed in the lower position be-

fore initial commissioning. Only work with the

machine if the riving knife (6) is in the upper

position. Fitting the riving knife (6) in the upper

position is as follows:

3. Loosen the locking handle (23) and push the riving

knife (6) in the upper position (Fig. 10).

4. The gap between the saw blade (5) and the riving

knife (6) should be a maximum of 5 mm (Fig. 11).

5. Re-tighten the mounting screw (23) and x the

table insert (6).

Saw blade guard assembly (Fig. 12)

1. Place the saw blade guard (2) including the bolt (24)

on the riving knife (4) from above so that the bolt is

tight in the slot of the riving knife (4).

2. Do not tighten the bolt (24) too much; the saw blade

guard (2) must be able to move freely.

3. Place the extraction hose (3) on the extraction adap-

ter on the rear of the machine and on the extraction

nozzle of the saw blade guard (2).

4. Disassembly takes place in reverse order.

Warning!

Before starting to saw, lower the saw blade

guard (2) on to the work piece.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toolson TS6000 PRO in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8.29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toolson TS6000 PRO Manual

Product: