Manual Toolson S-4-MINI (page 17 of 180) (English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish)

782277

Zoom out

Zoom in

1/180

screw.

The dimentions on the rail shows the cutting depth with-

out rail.

Saw blade replacement, Fig. 3,4, 5, 6

Caution: Before you are going to make the saw blade change,

switch off the machine and unplug the power cord.

1 Release Allen screw Fig. 3 (1) with the Allen key en-

closed Fig. 5 (2).

2 Fold the housing Fig. 3 (2) on the handle Fig. 3 (3)

upwards.

3 Fix the assembly key Fig. 5 (1) into the 2 holes on the

ﬂange Fig. 3 (7) and hold the key ﬁrmly in order to

release the Allen screw Fig. 3 (5).

4 Remove the ﬂange Fig. 3 (7), washer Fig. 3 (6), screw

Fig. 3 (5) and saw blade Fig. 3 (4).

(Caution: risk of injuries, wear protective gloves)

5 Insert new blade Fig. 3 (4) (observe direction of rotation

(4)), ﬂange Fig. 3 (7), washer Fig. 3 (6) and screw Fig.

3 (5). Using the assembly key Fig. 5 (1) hold the ﬂange

Fig. 3 (7) securely and tighten the Allen screw using

the Allen key Fig. 4 (2).

6 Fold the housing Fig. 3 (2) down fully, hold down and

tighten the Allen screw Fig. 3 (1) once more.

Operations

After having performed all the above procedures and

opera tions, you may begin cutting.

ATTENTION: Always keep hands away from the cutting

area and do not try to approach it when the machine is

running.

Switching the product on/off, Fig. 1

In order to switch on the circular plunge saw actuate the

two on/off switches (4). In order to switch off, release the

on/off switches (4).

Operating and holding the plunge-cut saw, Fig. 7

1 Secure the work piece so that it cannot get displaced

or moved while sawing.

2 Only move the saw forwards.

3 Grip the saw tightly with both hands ensuring that one

hand is placed on the main handle and the other on

the front handle.

4 When using a guide rail, it must be fastened with screw

clamps.

5 Make sure the power cable is not placed in the sawing

direction.

Sawing Fig. 1

1 Place the front part of the machine onto the work piece.

2 Switch the machine on using both on/off switches (4).

3 Press the plunge-cut trigger (3).

4 Push the saw downwards to reach the sawing depth.

5 Push the saw forward evenly.

6 After ﬁnishing the sawing cut, switch the machine off

and move the saw blade upwards.

Plunge-cuts, Fig. 8

1 Place the saw onto the work piece.

2 Place the cutting indicator with the rear arrow (A) on

the deepest plunge-cut position.

3 Switch the machine on and push the saw downwards

until you reach the set cutting depth.

4 Move the saw forwards until the cutting indication (C)

has reached the marked point.

5 After completion of the plunge-cut, move the saw blade

upwards and switch the saw off.

Sawing without rails Fig.1,3

1 Switch the machine on with the on/off switches Fig.

1 (4).

2 Position the saw at the desired cutting position with

the aid of the marking Fig. 3 (8).

3 Press the plunge trigger Fig. 1 (3).

4 Press the saw down in order to reach the sawing depth.

5 Slide the saw evenly forwards.

6 After ﬁnishing the saw cut, drive the machine up and

switch the saw off.

Cutting with rails (optional)

1 Place the machine in the guide rails. can be readjusted

using the hex driver Fig. 5 (2) included in the delivery,

when there is the risk of the adjusting screws Fig.2

(11) releasing by themselves.

2 Turn on the machine by pressing the on/off switch

Fig. (4).

3 Press the dip trigger Fig. 1 (3).

4 Press the saw downwards to reach the sawing depth.

During ﬁrst use the rubber lip is sawn off and thus

splitter protection is guaranteed up to the saw blade.

5 Push the saw uniformly forwards.

6 Turn off the machine and tilt the saw blade to the top

when the saw cutting is complete.

Sawing with dust suction Fig. 1

Connect the suction hose to the exhaust nozzle - Ø 35

mm (9).

m Electrical connection

The installed electric motor is completely wired ready for

operation.

The customer’s connection to the power supply system, and

any extension cables that may be used, must conform with

local regulations.

Defective electrical connection cables

Electrical connection cables often suffer insulation dam-

age.

Possible causes are:

• Pinch points when connection cables are run through

window or door gaps.

• Kinks resulting from incorrect attachment or laying of

the connection cable.

• Cuts resulting from running over the connecting cable.

• Insulation damage resulting from forcefully pulling out

of the wall socket.

• Cracks through aging of insulation.

Such defective electrical connection cables must not be

used as the insulation damage makes them extremely

hazardous.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toolson S-4-MINI in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2.54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toolson S-4-MINI Manual

Product: