Manual Toolson Pro HMD1800PRO (page 15 of 108) (English, German, Dutch, Danish, French, Italian, Swedish, Turkish, Norwegian, Finnish)

781902

Zoom out

Zoom in

1/108

15 І 108

Sound emission

Noise emission values are measured according to the

relevant standards.

Sound pressure level LpA 90 dB(A)

Uncertainty K 3 dB(A)

Sound power level LwA 101 dB(A)

Uncertainty K 3 dB(A)

Vibration ah2.90 m/s²

Uncertainty K 1.5 m/s²

• The indicated vibration emission value has been

measured using a standardized test procedure and

can be used to compare one electric tool with ano-

ther;

• The indicated vibration emission value can also be

used in a preliminary exposure assessment.

• Depending on how the power tool is used, the vib-

ration emission value may differ from the specied

value when the power tool is actually used;

• Try to keep the exposure to vibrations as low as

possible. Actions reducing the exposure to vibration

include, for example, wearing gloves when the tool

is used and limiting the working time. Here, all as-

pects of the operating cycle must be considered (for

example, the times when the tool is turned off, and

those when the tool is turned on but running without

load).

Storage

• The whole machine and all accessories must be tho-

roughly cleaned.

• Store the machine always out of children’s reach.

Put it in a secure position in a dry and safe place

where no extremely high or extremely low tempera-

tures may occur.

• Protect the stored machine from direct sunlight; put

it in a darkened area, if feasible.

• Do not wrap the machine into bags or covers made

of nylon or plastic, as dampness may develop.

Switching on/off

Do not use any device where the switch can not be

switched on and off. Damaged switches must be

repaired or replaced immediately by the customer

service.

Switching on (Fig.5)

• Operate the trip switch (5) at rst. Press the ON/

OFF button (4) on the handle.

Start the machine at the lowest rotational speed

(Level 1).

Switching off

• Release the ON/OFF handle button.

This machine is not suited for continuous opera-

tion.

Speed control (Fig.6)

With this type, the motor‘s speed and thus the agitator

performance can be adjusted. (Level 1 - 6).

• You can continuously adjust the speed with the

speed control (6).

2- speed gear (Fig.7)

The device is equipped with a 2-speed gear.

• For the speed selection turn the switch (7) by 180°.

1. speed: 0 min–1 - 450 min–1

2. speed: 0 min-1 - 790 min-1

Only operate this switch at standstill.

Working with the paint and mortar mixing tool

Before changing the mixing tool you must pull the po-

wer plug.

Reduce the working speed when you immerse the mi-

xing tool into the material you want to mix and when

you take it out again. When the mixing tool is fully im-

mersed, raise the speed to maximum in order to ensu-

re adequate cooling of the motor. Move the mixing tool

through the mixing container during the mixing operati-

on. Continue mixing until all the material has been tho-

roughly processed. When you are nished with your

mixing work, clean the mixing tool.

Cleaning and Maintenance

ATTENTION!

Unplug the power plug from the electrical outlet

before starting any work on the power tool.

Cleaning

• Keep the air vents of the machine clean in order to

prevent overheating.

• Clean the machine’s casing regularly with a soft

cloth, preferably after each use.

• Keep the air vents free from dust and dirt.

• If the dirt cannot be removed easily, use a cloth that

is moistened with soapy water.

ATTENTION!

Do not use solvents such as benzene, alcohol, am-

monia solutions, etc. These solvents may damage

the plastic parts.

Technical data

Nominal voltage 230 V~, 50 Hz

Power consumption 1800 W

Speed 0-450 min-1 / 0-790 min-1

Weight 7.2 kg

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toolson Pro HMD1800PRO in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Turkish, Norwegian, Finnish as an attachment in your email.

The manual is 3.66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toolson Pro HMD1800PRO Manual

Product: