Manual Toolson PRO-AS 360 (page 14 of 136) (All languages)

782589

Zoom out

Zoom in

1/136

14 І 136

cell damage inside the battery housing without this

overheating actually being apparent externally.

9 Avoid damage and shocks! Replace batteries which

have been dropped from a height of more than

one meter or which have been exposed to violent

shocks without delay, even if the housing of the bat-

tery pack appears to be undamaged. The battery

cells inside the battery may have suff ered serious

damage. In this respect, please also read the waste

disposal information.

10 If the battery pack suff ers overloading and overhe-

ating, the integrated protective cut-off will switch off

the equipment for safety reasons. Important. Do

not press the ON/OFF switch any more if the pro-

tective cut-off has actuated. This may damage the

battery pack

11 Use only original battery packs. The use of other

batteries may result in injuries, explosion and a re

risk.

Information on chargers and the charging process

1 Please check the data marked on the rating plate of

the battery charger. Be sure to connect the battery

charger to a power supply with the voltage marked

on the rating plate. Never connect it to a different

mains voltage.

2 Protect the battery charger and its cable from da-

mage and sharp edges. Have damaged cables re-

paired without delay by a qualied electrician.

3 Keep the battery charger, batteries and the cordless

tool out of children’s reach.

4 Do not use damaged battery chargers.

5 Do not use the supplied battery charger to charge

other cordless tools.

6 In heavy use the battery pack will become warm.

Allow the battery pack to cool to room temperature

before commencing with the charging.

7 Do not over-charge batteries! Do not exceed the

maximum charging times. These charging times on-

ly apply to discharged batteries. Frequent insertion

of a charged or partly charged battery pack will re-

sult in over-charging and cell damage. Do not leave

batteries in the charger for days on end.

8 Never use or charge batteries if you suspect

that the last time they were charged was more

than 12 months previously. There is a high pro-

bability that the battery pack has already suff ered

dangerous damage (exhaustive discharge).

9 Charging batteries at a temperature below 10°C will

cause chemical damage to the cell and may cause

a re.

10 Do not use batteries which have heated during the

charging process, as the battery cells may have

suffered dangerous damage.

11 Do not use batteries which have suffered curvature

or deformation during the charging process or

which show other non-typical symptoms (gassing,

hissing, cracking,…)

12 Never fully discharge the battery pack (recommen-

ded depth of discharge max. 80%) A complete di-

scharge of the battery pack will lead to premature

ageing of the battery cells.

13 Never charge the batteries unsupervised!

Protection from environmental in uences

1 Wear suitable work clothes. Wear safety goggles.

2 Protect your cordless tool and the battery charger

from moisture and rain. Moisture and rain can cause

dangerous cell damage.

3 Do not use the cordless tool or the battery charger

near vapors and inammable liquids.

4 Use the battery charger and cordless tools only in

dry conditions and an ambient temperature of 10-

ries and a re risk.

c) Keep unused batteries away from paper clips,

coins, keys, nails, screws and other metallic ob-

jects that could cause a short circuit between

the contacts. A short circuit between the battery

contacts may cause burns or a re

d) In case of incorrect use,  uid may escape from

the battery. Avoid contact with it. If you touch it

by accident, rinse the aff ected area with water. If

you get the uid in your eyes, also seek medical

advice. Leaking battery uid can cause skin irritati-

on or burns.

6. Service

a) Have your electric tool repaired only by trained

personnel using only genuine spare parts. This

will ensure that your electric tool remains safe to

use.

Hold the equipment by the insulated handles when

carrying out work during which the screw or the

plug-in tool could strike concealed power cables.

Contact with a live cable may also make the me-

tal parts of the equipment live and cause an electric

shock.

Additional safety instructions

We pay a great deal of attention to the design of every

battery pack to ensure that we supply you with batte-

ries which feature maximum power density, durabili-

ty and safety. The battery cells have a wide range of

safety devices. Each individual cell is initially formatted

and its electrical characteristic curves are recorded.

These data are then used exclusively to be able to as-

semble the best possible battery packs.

Despite all the safety precautions, caution must

always be exercised when handling batteries. The

following points must be obeyed at all times to en-

sure safe use. Safe use can only be guaranteed if

undamaged cells are used. Incorrect handling can

cause cell damage.

Important: Analyses conrm that incorrect use and

poor care are the main causes of the damage caused

by high performance batteries.

Information about the battery

1 The battery pack supplied with your cordless tool

is not charged. The battery pack has to be charged

before you use the tool for the rst time.

2 For optimum battery performance avoid low di-

scharge cycles. Charge the battery pack frequently.

3 Store the battery pack in a cool place, ideally at

15°C and charged to at least 40%.

4 Lithium-ion batteries are subject to a natural ageing

process. The battery pack must be replaced at the

latest when its capacity falls to just 80% of its capa-

city when new. Weakened cells in an aged battery

pack are no longer capable of meeting the high po-

wer requirements and therefore pose a safety risk.

5 Do not throw battery packs into an open re. There

is a risk of explosion!

6 Do not ignite the battery pack or expose it to re.

7 Do not exhaustively discharge batteries.

Exhaustive discharge will damage the battery cells.

The most common cause of exhaustive discharge

is lengthy storage or non-use of partly discharged

batteries. Stop working as soon as the performance

of the battery falls noticeably or the electronic pro-

tection system triggers. Place the battery pack in

storage only after it has been fully charged.

8 Protect batteries and the tool from overloads!

Overloads will quickly result in overheating and

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toolson PRO-AS 360 in the language / languages: All languages as an attachment in your email.

The manual is 4.09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toolson PRO-AS 360 Manual

Product: