Manual Toolson FS 920 PRO (page 20 of 56) (English, German, Swedish, Finnish)

781909

Zoom out

Zoom in

1/56

20 GB

Residual risks

Despite proper use, certain residual risk factors cannot

be eliminated fully. The following things can occur, de-

pending on the design and structure of the machine:

• Intervention in the running diamond cutting disc.

• Contact with the diamond cutting disc in exposed area.

• Ejection of work pieces and work piece components.

• Ejection of a faulty diamond attachment in the cut-

ting disc.

• Hearing damage due to non-use of the required hear-

ing protection.

• Injuries to the eyes due to non-use of eye protection

Any use beyond the one specied will be treated as im-

proper. The manufacturer will not be liable for damages

resulting from such improper use; the risk will be borne

by the user alone.

7. Before starting the equipment

Replace cracked diamond cutting discs.

• Get to know your machine. Familiarize yourself with

its use and its restrictions, but also with the specic

potential risks.

• Check the machine carefully for damages to ensure

that it is able to achieve the intended output. In case

of doubt, please replace the concerned component.

• Ensure that the switch is on Off, before inserting the

power plug into the mains socket.

• Ensure that the machine is cleaned and lubricated

properly.

• Before start-up, check the machine for damaged parts

and nd out whether these parts are working properly

and performing their dened function.

• Check the alignment of all moving parts, all broken

or fastening parts, and all other conditions that can

affect smooth operation. Each damaged part should

be repaired or replaced by a technician immediately.

• Do not use the machine if a switch cannot be activat-

ed/deactivated correctly.

Start-up of the leakage current circuit-breaker:

• The function should be checked before each start-up

and at regular Intervals (min. once every week).

• If the leakage current circuit-breaker does

not switch off properly during this test, there

is no personal protection! The device must

therefore be switched off immediately!

• In case of damages caused by the non-observation of

this operating instructions manual, all warranty claims

will become null and void. We do not accept any liabil-

ity for consequential damages.

• Check the product for damage before each use! If you

detect a damage, do not connect the product to the

mains power supply!

• After actuating the orange Reset button, the device

is ready for operation. Before operation, please test

the triggering with the help of the Test button (as de-

scribed in “Operation”).

• Insert the leakage current circuit-breaker into the

socket.

• Press the orange Reset button.

• A red symbol is displayed in the window indicating op-

erational readiness.

• Press the red Test button. This action simulates a

leakage current.

• If the machine is working properly, the circuit-breaker

will disconnect the load from the mains. This is dis-

played in the window through the disappearance of

the red symbol.

• Protection of man and animal is effective only if the

machine works properly.

• The Reset button must be pressed a second time for

operation.

• The load can now be inserted.

8. Attachment and operation

Assembly Fig.3-5

For packaging purposes, your machine

is not fully assembled.

1. Remove the machine from the packaging and place

carefully to one side on the ground.

2. Unscrew the star knob screw (A) and fold the sup-

porting feet down. Re-tighten the star knob screw

(Fig. 3)

3. Place the machine on the feet.

4. Install the handle onto the motor housing using 2

hexagon screws (B) (Fig. 4).

5. Secure the cooling water pump (13) into the pre-

scribed position in the water pan (4)

6. Fill the water pan until the water pump is completely

covered with water. Ensure that the discharge is

sealed securely.

Before starting the equipment

• Install the machine on an even, slide-proof oor.

• Check that the voltage on the nameplate matches the

existing voltage; connect the power plug to the mains

power supply only thereafter

• The cutting disc should be free to run before the ma-

chine is switched on.

Caution: Cutting disc must always be cooled with water.

Caution: Cutting disc runs with a time lag.

Do not break the cutting disc by applying pressure at the

sides.

• Under normal use conditions, the motor casing can

become hot.

• Do not use force on the machine or on an accessory

to achieve the performance of a bigger Industrial ma-

chine. It does a better job at the output for which it is

designed.

• Dene all machine settings only when it is switched

off.

• Do not leave the machine unattended as long as it

is running.

• During shutdown, leave the machine only after it

comes to a complete standstill.

• Always switch the machine off before pulling out the

power plug from the mains socket.

• Always pull out the power plug. Never disconnect the

power plug from the mains socket by pulling at the

cable.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toolson FS 920 PRO in the language / languages: English, German, Swedish, Finnish as an attachment in your email.

The manual is 5.2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toolson FS 920 PRO Manual

Product: