622267
9
Zoom out
Zoom in
Previous page
1/15
Next page
TM 81006 English
www.toolland.eu 9
INSERTING AND REMOVING A DRILL OR
SCREW BIT
Open the chuck.
Insert the drill or the screw bit in the
chuck.
Fasten the chuck by hand.
Fasten the chuck firmly by inserting the
chuck key in one of the holes in the side
of the chuck and turning it clockwise.
In order to remove a drill or screw bit,
you proceed in reverse order.
Before inserting or removing a drill
or screw bit always pull the plug
from the wall socket.
MOUNTING THE SIDE GRIP
Loosen the side grip
Slide the side grip over the chuck and
onto the machine.
Turn the side grip into the required
position and tighten it firmly.
MOUNTING THE DEPTH STOP
The depth stop is used to limit the maximum
drilling depth.
Loosen the side grip.
Insert the depth stop into the hole in the
side grip.
Set the depth stop to the required drilling
depth.
Tighten the side grip firmly.
SELECTING THE OPERATING MODE
Select the required operating mode before
use (drilling or hammer drilling).
For drilling in wood, metal, plastics and
soft stone and for driving screws, turn
the drill symbol on the switch to the
arrow.
For drilling in masonry, turn the hammer
and drill symbol on the switch to the
arrow.
Always wait until the motor has
come to a complete standstill
before changing the operating
mode.
FORWARD/REVERSE SWITCH
Push the forward/reverse switch to the
left to drill holes and fasten screws.
Push the forward/reverse switch to the
right loosens screws.
Always wait until the motor has
come to a complete standstill
before changing the direction of
rotation.
ADJUSTING THE SPEED
This machine has been fitted with an
adjusting wheel for the maximum speed.
Turn the adjusting wheel as indicated on
switch to set the maximum speed.
SWITCHING ON AND OFF
To switch the machine on, press the
on/off switch. The further you press the
switch, the higher the speed of the
machine.
To switch off the machine, release the
on/off switch.
To switch the machine to continuous
mode, keep the on/off switch pressed and
at the same time press the lock-on/off
switch.
To switch off continuous mode, press the
on/off switch again.
TECHNICAL SPECIFICATIONS
Voltage
230V
Frequency
50Hz
Power
850W
Speed (under load)
3.000t/min
Drilling capacity
Wood
25mm
Steel
10mm
Concrete
13mm
Weight
1,8kg
Level of sound pressure measured according
to EN-standards:
Lpa (sound pressure)
99,4dB(A)
k=3dB(A)
Lwa (acoustic power)
110,4dB(A)
k=3dB(A)
Weighted root mean square acceleration
value according to EN 60745:
6,643m/s² k=1,5m/s²
WARANTY
Refer to the enclosed warranty conditions for
the terms and conditions of warranty.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toolland TM 81006 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toolland TM 81006 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info