549761

Tomy Digital SR200 Manual

2
Zoom out
Zoom in
Previous page
1/32
Next page
GB
BABY UNIT
• GETTING TO KNOW YOUR MONITOR
PARENT UNIT
Microphone AC Adaptor jack
Power Indication Light
Power ON/OFF Button
Volume Control Buttons
Sound Level Lights Display
LINK Indication Light
Power Indication Light
Speaker
Sound Activated
Monitoring Light
Sound Activated
Monitoring Button
Power ON/OFF Button
Belt Clip/Battery
Compartment Cover
AC Adaptor Jack
•••
Low Battery on the Parent Unit
Power Indication Light will change
from solid green to ashing red.
Alarm tone on
Parent Unit
Alarm Meaning
Indications on the Parent Unit
Out of range
LINK Indication Light will change
from solid green to ashing red.
(Continuous)
3 beeps
••••••••
Fig.1 Fig.2
Fig.3
• PARENT UNIT
Unscrew the battery compartment cover from the back of the unit (N.B: this
may already be supplied loose). Next, link the plug on the end of the battery
pack connector to the socket inside the unit, pushing the plug rmly into
the socket until it clicks. Place the battery pack into the compartment and
screw the cover back into position. See Figure 1.
Ensuring the power cable is correctly connected, plug your Parent Unit into
the mains supply and charge for a full 7 hours. See Figure 2. You can use
your monitor while it is charging by following the ‘SET UP’ guide below.
Important! Your Parent Unit will not function without rst inserting the battery pack.
• BABY UNIT
The Baby Unit is powered by your domestic mains supply, using the power adaptor supplied.
Connect the adaptor to the back of the unit as shown in Figure 3.
Position the Baby Unit at least 1 metre away from your baby, ensuring all parts are kept out of
reach. Under no circumstances should you place any parts of the monitor in or on a cot. For
best performance, we recommend that the monitor is placed no further than 3 metres away
from your baby.
• SET UP
• POWER ON
Make sure both the Baby and Parent Units are plugged into the mains and that the Parent Unit has its battery pack
installed (see above). The units should stand at least 1 metre apart.
Activate the Baby Unit by pressing and holding the ON/OFF Button
on the back of the unit until the green Power
Indication Light on the front lights up.
Next, activate the Parent Unit by pressing and holding the ON/OFF Button
located on the back (next to the battery
compartment cover) until the green light illuminates.
Note: If the Parent Unit is switched on before the Baby Unit, an out-of-range alarm will sound if the Baby Unit is not
switched on within 30 seconds.
• POWER OFF
Switch off the Parent Unit by pressing and holding the ON/OFF Button
until the green light goes out.
Then, press and hold the Baby Unit’s ON/OFF Button
until the light goes out.
• BABY AND PARENT UNIT CONNECTION
As each unit activates, the LINK Indication Light
on the Parent Unit will ash as both Units auto-search and link to
each other. Once a connection is made between Baby and Parent Units, the LINK Indication Light will glow green
constantly and normal monitoring will start. The Sound Level Lights Display reacts to sound: the louder the sound, the
more lights illuminate.
• ALARM MODES
Identify the cause of an audible alarm by using the following table; should you be unable to identify or rectify the
cause of the problem, please refer to the Simple Solution Guide in these instructions.
GB
2
3
2 3
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tomy Digital SR200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tomy Digital SR200 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 5,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info