382623

Toledo tks 160 Manual

4
Zoom out
Zoom in
Previous page
1/30
Next page
4 8 10 3 1 2 14
5 6 7 11 9 12 13
max 5 mm
max 5 mm
3
2
1
1 2
3
1
2
80
A=45°
B=90°
1
2
1
2
A B
1
4 3 5
2
Toledo 57
3. ASSEMBLY INSTRUCTIONS
THE NUMBERS IN THE FOLLOWING TEXT COR-
RESPOND WITH THE FIGURES AT PAGE 37.
DESCRIPTION (fig. 1)
Before adjusting the saw, make sure the
tool is disconnected.
ADJUSTING THE RIVING KNIFE (fig. 2)
- Move the blade guard backwards and lock by
means of knob (1).
- Use a screwdriver to loosen both screws (2).
- Adjust the riving knife, referring to the distances
indicated in the drawing.
Retighten both screws (2) and release knob (1).
- Check that the riving knife is exactly behind the
blade.
ADJUSTING THE CUTTING ANGLE (fig. 3)
- Loosen both knobs (1).
- Move the shoe (2) into the proper position (0°-
45°). The cutting angle is indicated by the pointer
(3).
ADJUSTING THE DEPTH OF CUT (fig. 4)
- Loosen knob (1).
- Move the shoe (2) downwards.
- The depth of cut can be checked (3).
- After adjustment retighten knob (1).
MOUNTING THE PARALLEL GUIDE (fig. 5)
- Loosen knob (1).
- Insert the guide into the relevant recesses (2).
- Set the required width and retighten knob (1).
REPLACING OR CLEANING THE BLADE
(fig. 6)
Before adjusting the saw, make sure the
tool is disconnected.
- Move the blade guard backwards and lock by
means of knob (1).
- Lock-up the shaft with the spindle lock.
- Use an hexagonal key (2) to loosen the left-hand
bolt in the centre of the blade.
- Remove the blade and clean or replace.
- Put the blade back in its proper position, making
sure the teeth of the blade point in the same direc-
tion as those of the riving knife (4).
Fit the locking ring (5) and retighten the left-hand
bolt.
After fitting a new blade it may be necessa-
ry to readjust the riving knife.
- Release knob (1) to put the guard back in place.
REPLACING THE CARBON BRUSHES (fig. 7):
Frequent use will cause the carbon brus-
hes to wear down. Regular inspection, after
every 100 hours of use, is essential. If the
brushes have worn down to less than 4mm,
replace.
- Remove both screws (1).
- Take the brushes (2) out and check.
- Reinsert the brushes into the relevant recesses.
Make sure the copper part of the brushes firmly
touches the copper part in the recess.
- Retighten the screws (1).
SWITCHING ON/OFF (fig.7)
- Depress knob (B) with your right-hand thumb
and keep it depressed.
- Depress knob (A) to start the tool.
- Release knob (A) to stop the tool.
!
!
!
!
1. Handle
2. Spindle lock
3. On/off switch
4. Depth of cut adjusting
knob
5. Mains lead
6. Riving knife
7. Blade guard
8. Hexagonal bolt
9. Shoe
10. Flange
11. Saw Blade
12. Parallel stop
13. Parallel guide adjus-
ting knob
14. Cutting angle adjus-
tingknob
4 Toledo
FIG. 1
FIG. 2
FIG. 3
FIG. 4 FIG. 5
FIG. 6
FIG. 7
45
30
0
1
2
3
3
4
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toledo tks 160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toledo tks 160 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info