692132
12
Zoom out
Zoom in
Previous page
1/36
Next page
12
11. AC inlet
Connect the supplied power cord to this inlet. The socket-outlet should be installed near the equipment
and the plug (disconnected device) shall be easily accessible.
12. Functional ground terminal [SIGNAL GND]
Hum noise may be generated when external equipment is connected to the unit. Connecting this
terminal to the functional ground terminal of the external equipment may reduce the hum noise.
13. LINE 1, LINE 2, LINE 3, LINE 4 INPUT TERMINAL
10 k–10 dB*unbalanced RCA Jack (Upper and lower of RCA input signal is mixed)
Connect music source equipment: e.g: CD players.
14. LINE 1, LINE 2, LINE 3, LINE 4 INPUT LEVEL CONTROL
Adjust the input level (sensitivity) of LINE 1, LINE 2, LINE 3, LINE 4.
15. ASSIGNMENT RESTRICTION DIP SWITCHES (LINE 1, LINE 2, LINE 3, LINE 4)
Assign restriction LINE 1, LINE 2, LINE 3, LINE 4 to CH1, CH2, CH3, CH4 outputs.
LINE 1 ASSIGNMENT RESTRICTIONS:
Switch No. ON OFF
1 LINE 1 can’t be assigned to CH1 LINE 1 can be assigned to CH1
2 LINE 1 can’t be assigned to CH2 LINE 1 can be assigned to CH2
3 LINE 1 can’t be assigned to CH3 LINE 1 can be assigned to CH3
4 LINE 1 can’t be assigned to CH4 LINE 1 can be assigned to CH4
Note: 1)
The functionality for LINE 2, LINE 3, LINE4 is the same as LINE 1.
2) When the assignment restriction is set, both INPUT SELECT SWITCH (10) or connected
WP-700, are not allowed to select the restricted channel.
16. MIC/LINE input terminal (PRIORITY 1, PRIORITY 2)
MIC: 2.2K, –60 dB*/ LINE: 2.2K, –10 dB*, electronically-balanced inputs of 3-pin removable terminal
block type.
Connect microphone or line level music source equipment. MIC/LINE gain could be from the PRIORITY
FUNCTIONAL DIP SWITCH (20) #6.
17. MIC/LINE input level control (PRIORITY 1, PRIORITY 2)
Adjust the input level (sensitivity) of the MIC/LINE
18. Manual mute terminal
Open voltage: DC 3.3V, Short current: <5mA
1) When (+), (-) shorted: The selected LINE 1, LINE 2, LINE3, LINE4 input signal to CH1, CH2, CH3,
CH4 output will be muted, and switch to the page channel (1st ~4th switch of (20)) that have been
assigned by PRIORITY 1, PRIORITY 2 inputs.
2) When (+), (-) openedCH 1, CH 2, CH 3, CH 4 output will gradually recovered from the previous
assigned LINE 1, LINE 2, LINE3, LINE4 signal. The recovery time is controlled by the HOLD TIME
control (19).
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toa MM-700F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toa MM-700F in the language / languages: English as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info