575736

Tizzbird Wi-Fi 1080p Streaming Guide Manual

3
Zoom out
Zoom in
Previous page
1/5
Next page
TizzBird Wi-Fi 1080p
Streaming Guide
For Smart TV Stick N1
And Other Tizzbird Products
2
1. Objective
This documentation is intended to provide a proper guide to stream high resolution
contents such as
1080p MKV file or You-Tube HD
to Tizzbird N1 and other Tizzbird products
thru
Wi-Fi.
The decoding capability of Tizzbird N1 is fairly high so it can decode 1080p H264
stream up to 15 mbps without problem. It can also decode the 1080p MPEG2 stream up to
25 mbps, and you can confirm it with connecting USB flash drive or external HDD. But its
decoding capability is quite limited when streaming thru Wi-Fi, not by decoding
performance but by Wi-Fi throughput.
The nature of “Smart Stick” device confines this decoding capability because of Wi-Fi
performance. So the setting up the proper streaming environment is quite important.
This documentation describes the steps as following.
1) Setting up the Wi-Fi access point properly.
2) Setting up “Network Server” for maximum performance.
3) Setting up “Audio & Visual “ parameter properly to maximize throughput.
If you follow these steps, the 1080p MKV streaming thru Wi-Fi can be done without any
problem at Tizzbird N1. You can also get the beautiful You-Tube HD contents.
3
2. Setting Up Wi-Fi and Wi-Fi Access Point
Setting up the Wi-Fi and AP (Access Point) is
the single most important factor
that
determines overall streaming performance.
1) Please SETUP Wi-Fi ACCESS POINT to 802.11n mode only.
- This is the most important and it will remove many potential streaming problems
between SERVER and Tizzbird N1.
- Normally Wi-Fi access point is set to 802.11b/g/.n mode, and it will prevent Tizzbird N1
from maximum connection speed. The legacy Wi-Fi devices such as older model
notebook, smart phone will try to connect Wi-Fi by 802.11g then the speed of Wi-Fi is
confined to 802.11g.
- Please refer to Wi-Fi Access Point manual to change the 802.11n mode only. Normally
it’s possible thru web-browser. The access point normally provides configuration page
thru WEB. For example open the browser and type the http://192.168.1.0 “ will pop up
the configure window of access point.
- If you still want to use Wi-Fi access point on other legacy 802.11g devices, GO GET NEW
ACCESS POINT for streaming purpose only. It’s quite cheap and only $20 or so. Please
don’t try share the ACCESS POINT with other legacy devices. It will ruin
everything. Please don’t complain to us when using N1 with other legacy 11g devices.
There’s nothing much we can do here.
2) Check up the connection speed by “Settings” > “Network” at Tizzbird as following figure. The
“Wi-Fi Setting” item shows the current connection speed. It should be more than 54
mbps. The 54 mbps means it’s connected with 802.11g mode. The best is 150mbps
connection speed.
3) Install the Wi-Fi access point as close as possible with Tizzbird N1. The access point should
reside at direct seeing position where N1 resides at least.
4
3. Setting Up the Network Server
Setting up the “Network Sever” is the next step. Here’s the golden rule. If you want to
stream high-res contents thru Wi-Fi, DON’T USE SAMBA protocol. Samba is O.K. for
Ethernet, but its efficiency will drop to half at least compared to NFS or DLNA. Please use
the NFS or DLNA protocol to stream via Wi-Fi.
1) To use NFS on PC, please install the “TizzNFS” at following Tizzbird website.
http://www.tizzbird.com/eng/index.php?mm_code=726&sm_code=727
2) To use DLNA, turn DLNA “On” at “Settings” > “Network” > “DLNA”. DLNA server can be
browsed at “File Browser”.
3) Select proper protocol (NFS) at “Network Server” configuration as following figure.
.
5
4. Setting Up Audio & Visual
If you did up to here, most of jobs are done. And most of contents except high bitrate
BD will be playback without problem. Please don’t forget install Wi-Fi access point at direct
seeable area of N1.
The following tips will help the smoother contents streaming specially 1080p.
1) Turn “Native Frame Rate” ON. Turning on “Cinema Original (24p)” will help a lot. It will
help the load-balancing of CPU to decode & scaling. So you will get smoother playback and
higher bitrate contents.
2) If your TV or AV receiver supports the Dolby or DTS digital audio decoding, then setting up
audio to “HDMI Digital” will help reducing burden of audio decoding of CPU.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tizzbird Wi-Fi 1080p Streaming Guide at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tizzbird Wi-Fi 1080p Streaming Guide in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info